Guiding Signals

 

 

Control Buttons

Indicator

Projector Status

Description

 

 

 

Power

TEMP

LAMP

 

 

 

 

(Amber)

(Amber)

 

 

 

 

 

 

 

 

Standby mode

Projector in Standby mode. Ready to power

BLUE

OFF

OFF

 

on.

Flashing

 

 

 

 

 

 

 

 

Warming up

Projector takes some time to warm up and

BLUE

OFF

OFF

mode

power on.

 

 

 

 

 

 

 

 

Lamp on

Projector in Normal mode, ready to display

 

 

 

 

an image.

BLUE

OFF

OFF

 

Note: The OSD menu is not accessed.

 

 

 

 

 

 

 

 

Cooling mode

Projector is cooling to shutdown.

BLUE

OFF

OFF

 

 

 

 

 

Cooling before

The projector takes 60 seconds to cool

 

 

 

Power Saving

down before entering Power Saving mode.

AMBER

OFF

OFF

mode

 

 

 

 

 

 

 

 

 

Projector

Air vents might be blocked or ambient

 

 

 

overheated

temperature may be above 35 ºC. The

 

 

 

 

projector automatically shuts down. Ensure

 

 

 

 

that the air vents are not blocked and that

OFF

AMBER

OFF

 

the ambient temperature is within

 

 

 

 

operational range. If the problem persists,

 

 

 

 

contact Dell.

 

 

 

 

 

 

 

 

Lamp driver

The lamp driver is overheated. The air

 

 

 

overheated

vents may be blocked. The projector

 

 

 

 

automatically shuts down. Turn the display

AMBER

AMBER

OFF

 

on again after the projector cools down. If

 

 

 

 

the problem persists, contact Dell.

 

 

 

 

 

 

 

 

Fan breakdown

One of the fans has failed. The projector

 

AMBER

 

 

automatically shuts down. If the problem

ÒFF

OFF

 

Flashing

 

persists, contact Dell.

 

 

 

 

 

 

 

 

 

 

 

Lamp driver

The lamp driver has failed. The projector

 

 

 

breakdown

automatically shuts down. Unplug the

AMBER

 

AMBER

 

power cord after three minutes and then

OFF

 

Flashing

Flashing

 

turn the display on again. If this problem

 

 

 

 

 

 

persists, contact Dell.

 

 

 

 

 

 

 

 

Color Wheel

Color wheel cannot start. The projector has

 

 

 

breakdown

failed and the projector automatically shuts

 

AMBER

AMBER

 

down. Unplug the power cord after three

BLUE

 

Flashing

Flashing

 

minutes and then turn on the projector. If

 

 

 

 

 

 

this problem persists, contact Dell.

 

 

 

 

 

 

 

 

Lamp failure

Lamp is defective. Replace the lamp.

OFF

OFF

AMBER

 

 

 

 

 

Fault - DC supply

Power supply has been interrupted. The

 

 

 

(+12V)

projector automatically shuts down.

AMBER

 

 

 

Unplug the power cord after three minutes

AMBER

AMBER

 

Flashing

 

and then turn on the projector. If this

 

 

 

 

 

 

 

problem persists, contact Dell.

 

 

 

 

 

 

 

 

Lamp module

Lamp module connection may be

 

 

 

connection failed

disrupted. Check the lamp module and

OFF

OFF

AMBER

 

ensure that it is properly installed. If the

Flashing

 

 

 

problem persists, contact Dell.

Troubleshooting Your Projector

 

105