Access Under Mounting Location | Humminbird 957C manual

www..reelschel matic..com

Access Under Mounting Location

Follow these steps to deck mount the GPS receiver when routing the cable down through the mounting location:

1.Determine the best location, then test route the 20' (6 m) cable from the mounting location to the control head.

NOTE: Installation details may vary with unit configuration.

2.Mark the mounting location and drill a 3/4" (19 mm) hole for the cable and cable plug. Route the cable.

3.Cover the cable hole with the receiver. Make sure the receiver is flush on the surface and mark the two mounting holes with a pencil or punch.

4.Move the receiver to the side and drill two pilot holes using a 9/64" (3.5 mm) bit.

NOTE: Remember to caulk or seal screw holes and drilled holes as needed to protect your boat from water damage.

5.Align the GPS receiver screw holes over the pilot screw holes and attach with the #8 - 1 1/4" Phillips head screws. Hand tighten only!

NOTE: If the mounting surface is thin and made of a lighter material, a backing material may be needed below the mounting surface.

Access Under Mounting Location

No Access Under Mounting Location

No Access Under Mounting Location

Follow these steps to deck mount the GPS receiver in a situation where you must route the cable to the side because there is no space for a cable underneath the mounting location.

1.Determine the best location, then test route the cable from the mounting location to the control head.

NOTE: AS-EC10 10' extension cables are available from Humminbird® if your planned routing exceeds 20', (6 m). Maximum cable length, including extensions, should not exceed 50' (16 m).

2.Confirm the cable length is good and route the cable from the receiver to the control head. If holes are required to route the cable, they must be 3/4" (19 mm) to allow for the cable connector. Secure the NMEA pigtail with electrical tape.

NOTE: Remember to caulk or seal screw holes and drilled holes as needed to protect your boat from water damage.

27

Image 35

Humminbird 957C manual No Access Under Mounting Location

Contents

Page Thank You Table of Contents Quad Layout Upper Range Delete Recording Start RecordingDelete Image Delete All Images Navigation Menu Tab Views Menu Tab Page How Sonar Works Series Introduction DualBeam Plus Sonar Peak to Peak measures power output at the highest points Purchase for 917c Combo models only QuadraBeam Plus SonarUniversal Sonar How GPS and Cartography Work GPS uses a constellation of 24 satellites that Multi-Media Card MMC/SD Slot Software Updates Accessory BusInstallation Overview Installing the GPS Receiver if included Control Head InstallationBasic installation tasks that you must perform include Washer Gimbal Knob Gimbal Bracket Gimbal Mounting the Control Head Mounting Screws Cables Routed Directly Beneath Mounting Bracket Cables Routed Behind Mounting Bracket Connecting the Control Head Power Cable to the Boat Transducer Installation Locating the transducer mounting location Transom Transducer Installation Level Preparing the Mounting Location Assembling the Transducer and Initial Mounting Knuckle Mounting the Assembly to the Transom Seam aligned with boat hull Routing the Cable Screw Connecting the Cable Test and Finish the Installation Correctly, Inside the Hull Transducer Installation Determine the transducer mounting location Trial installation Permanently mount the transducer Route the cable Are included with the bracket Trolling Motor Transducer Installation If you have… Then use GPS Receiver InstallationTrolling Motor Transducer Options Abrasion Stem Mounting with an Existing 1 14 Thread StemFollow these steps to stem mount the GPS receiver No Access Under Mounting Location Access Under Mounting Location Finish Routing the Cable Check GPS Receiver Operation To test the installation Testing the System Installation Powering Up the Control Head Getting Started Using Your 900 Series Triplog What’s On the Sonar Display Bottom Presentation Understanding Sonar HistoryReal Time Sonar RTS Window Key Functions POWER/LIGHT Key Menu Key View Key Exit Key View Preset keysWAY Cursor Control Key Goto Key has multiple functions, depending on the situation Info KeyMark Key Goto Key Views and Readouts Zoom +/- KeysViews Sonar View Sonar View Sonar Zoom View Sonar Zoom View Split Sonar View Split Sonar View Snapshot and Recording View Page Recording Slider Bar Recording Playback Only with QuadraBeam Plus transducer Side Beam View 555 Bird’s Eye View Bird’s Eye View Chart/Bird’s Eye Combo View Chart/Bird’s Eye Combo View Chart/Chart Combo View Chart/Chart Combo View Chart View with Active Cursor Chart View Chart/Sonar Combo View Chart/Sonar Combo View Viewing Cartography Chart Orientation Navigation Waypoints, Routes and Tracks Waypoints, Routes and Tracks Save, Edit, or Delete a Waypoint Add a Waypoint Target or Trolling Grid Navigate to a Waypoint or Position Save, Edit or Delete a Route Edit, Delete or Hide Saved Tracks Save or Clear a Current Track MOB Navigation Man Overboard MOB Navigation Com Normal Simulator System Status Start-Up Options MenuUp Options menu System Status Exit Normal operation by powering your 900 Series offNormal Operation Simulator Self Test Accessory Test GPS Diagnostic View Active Side Sonar X-Press Menu Sensitivity Split Position Advanced Sonar, Split Sonar Active Sonar Side Views only Upper RangeLower Range With QuadraBeam Plus Transducer, Side Beam View only Chart SpeedQuad Layout Sonar Colors Cancel NavigationBottom Lock Bottom Range Navigation X-Press Menu Only with an active cursor on a waypoint Chart or Combo view onlyWaypoint Name Cursor to Waypoint Skip Next Waypoint Save Current TrackClear Current Track Save Current Route Remove Grid Cancel MOB NavigationTo Cancel MOB Navigation Remove Target Most recently-created waypoint Optional-purchase MMC/SD Card, Snapshot Recording View only Start RecordingStop Recording Snapshot and Recording View only To delete an image Delete ImageDelete All Images Delete All Recordings Delete Recording To specify playback speed Pings Per SecondPlayback Speed Sonar Menu Tab Stop Playback Transducer will be displayed on the screen Beam SelectFish ID+ Fish ID Sensitivity Zoom Width Bottom View Optional-purchase for To change the 455 kHz Sensitivity settingKHz Sensitivity Advanced Depth LinesSurface Clutter Max Depth Noise Filter Color Bar Water TypeTransducer Select Navigation Menu Tab Temperature GraphSonar View only, with Temperature input Saved Tracks Current Track Waypoints Submenu contains the following menu choices WaypointsRoutes North Reference Track Min Distance Trolling Grid RotationTrackpoint Interval Export All Nav Data Track Color RangeMap Datum Course Projection Line Delete All Nav Data Continuous Navigation ModeChart Menu Tab Continuous Navigation Mode allows you to Map Borders Chart Detail Level Shaded Depth Lat/Lon GridSpot Soundings Navaids on Birds Eye View Set Map Offset Set Simulation Position Clear Map Offset Alarms Menu Tab Low Battery Alarm Depth AlarmFish ID Alarm Temp Alarm Aux Temp Alarm Off Course Alarm Arrival Alarm Alarm Tone Drift Alarm International only Setup Menu TabUnits Depth Units Temp Language User ModeUnits Distance Units Speed Select Readouts Triplog ResetRestore Defaults Off Triplog Position Voltage Aux. TemperaturePage Temp Offset Depth OffsetAux Temp Offset Position Format Speed CalibrationLocal Time Zone Daylight Saving Time Advanced, International only Time FormatDate Format Nmea Output Digits Format Views Menu Tab Following views are available Using Screen Snapshot Accessories Menu Tab To turn Screen Snapshot on or off Series Doesn’t Power Up Troubleshooting Control head loses power at high speeds Display Problems Finding the Cause of Noise Humminbird Service Policy Year Limited Warranty Returning Your Unit for Service Series include Series AccessoriesPage Specifications Glossary 123 Com Atic Receiver See Transmitter Com Atic Sonar Terms Glossary GPS & Navigation Terms 129 Glossary GPS & Navigation Terms Glossary GPS & Navigation Terms Glossary GPS & Navigation Terms Contact Humminbird