Manuals / Husqvarna / Lawn and Garden / Brush Cutter

Husqvarna 343R, 345RX, 343F, 345FX, 345FXT 502 54, Electrical system, Dismantling, 502 51, 502 50

Models: 343R, 345RX, 343F, 345FX, 345FXT

1 63

Download 63 pages 2.84 Kb

Page 12

502 54 15-01

Electrical system

2

Dismantling

Remove the starter, cylinder cover, and spark plug.

Attach piston stop no. 502 54 15-01.

502 54 15-01

Remove the nut holding the flywheel.

Remove the flywheel.

502 51 94-01

Remove the ignition module and the generator.

502 50 18-01

Dismantling

Remove the starter, cylinder cover, and spark plug.

Fit piston stop no. 502 54 15-01 in the spark plug hole.

NOTE!

Place the piston stop so it is caught between the piston and the cylinder head. Not so it sticks out into the exhaust port.

Remove the nut holding the flywheel.

Remove the flywheel from the crank- shaft using punch no. 502 51 94-01.

Leave a gap of approx. 2 mm between the punch and the flywheel.

Gently knock the punch with a hammer while holding the flywheel with your other hand.

Dismantle the ignition module.

Remove the ignition cable from the holder (A).

Remove both bolts (B).

Loosen the short-circuit cable (C) from the ignition module.

Remove the generator (D) that supplies power to the heated handles.

11

Image 12

Husqvarna 343R, 345RX, 343F, 345FX, 345FXT manual 502 54, Electrical system, Dismantling, 502 51, 502 50

Contents

English 343R 345RX 343F 345FX 345FXTWorkshop manual Model 343R, 345RX, 343F, 345FX, 345FXT Contents General recommendations ___________________1.Starter __________________________________ 2.Electrical system _________________________General recommendations RememberSpecial tools Fire riskContents 1 Starter1Starter DismantlingDismantling Assembly StarterAssembly Replacing the drive dogs 1StarterReplacing the drive dogs Electrical system ContentsAssembly _________________________________ Checking the ignition spark ____________________Electrical system Checking the ignition spark502 71 Checking the ignition sparkElectrical system Replacing the spark plug cover502 50 Electrical system502 54 Electrical systemDismantling DismantlingDrive dogs Heated handlesDo not pry off the heating element before the locking catch has beenWiring diagram Electrical systemElectrical system Fuel system ContentsAssembly _________________________________ Carburettor settings _________________________Fuel system Air filterAir filter Tank venting Fuel filterMassage the oil into the air filter Fuel systemFuel pump CarburettorDismantling Fuel systemThe carburettor’s design The metering unitThe blending unit Fuel systemThe pump unit Dismantling the carburettorFuel system The pump unitFuel system In the event of leakage – remove the needle valveNote how the jets are positionedFor example, the H-needleis a little shorter than the L-needleAssembling the carburettor Use Loctite on the valve screwsFuel system Assembling the carburettorare not bent or pinched when the The H-needleis a little shorterthan the L-needle Check carefully that the fuel hosesCarburettor settings Basic settingFine adjustment Functionsetting Correctly adjusted carburettorThe recommended max. speed must not be exceeded Idling speed T-screwCarburettor adjustment 345RX/FX adjustment 345RX/FXAdjusting the L-needle Adjusting the HCheck for wear on pins A and B Fuel systemDisassemble the throttle control A, the lock to prevent accidental throttle operation B, the start throttle lock C and the throttle stop D in order to check if replacement is necessary Fuel systemPage 4 Centrifugal clutch ContentsAssembly _________________________________ Dismantling ________________________________Centrifugal clutch 502 21Dismantling DismantlingCentrifugal clutch 502 54Clutch drum 502 11Assembly AssemblyChange the bearings in the clutch housing if necessary Centrifugal clutchPage 5 Angle gear ContentsAssembly _________________________________ Dismantling ________________________________Angle gear Let the small circlip around the axle remainDismantling Dismantling503 97 AssemblyAngle gear Shaft 503 80Angle gear Shaft6 Cylinder and piston ContentsCleaning, inspection _________________________ Assembly _________________________________Cylinder and piston DismantlingTurn the valve the right way when fitting Decompression valveCylinder and piston Decompression valveCleaning, inspection manifold is fitted using aInlet manifold Exercise caution if the inletAnalysis and actions Insufficient lubricationCause ActionPiston scoring caused by heavy carbon deposits Cylinder and pistonCause ActionPiston damage caused by a too high engine speed Piston ring breakagePiston ring guide pin Damage caused byForeign objects Cylinder and pistonCause ActionService tips DefectBe careful with the lower edge of the piston ring groove. If this is damaged, or if carbon depositsWear tolerances Cylinder borePiston ring gap Piston ring groove7 Crankshaft and crankcase ContentsAssembly _________________________________ Leakage testing the crankcase _________________Crankshaft and crankcase DismantlingDismantling Crankshaft and crankcase 502 52Inspecting the crankshaftCrankshaft and crankcase Inspecting theAssembly AssemblyCrankshaft and crankcase 502 50Leakage testing the crankcasePress down the sealing plates as far as possible between the boltsHusqvarna E-Tech 503 55Crankshaft and crankcase Page Tools ContentsStarter __________________________________ Electrical system __________________________List of tools 505 38Starter ElectricalList of tools gearCrankshaft Workshop114 01 2003W24