Manuals / Husqvarna / Lawn and Garden / Brush Cutter

Husqvarna 343R, 345RX, 343F, 345FX, 345FXT manual 1Starter, Dismantling

Models: 343R, 345RX, 343F, 345FX, 345FXT

1 63

Download 63 pages 2.84 Kb

Page 5

Image 5

1Starter

WARNING!

Protective glasses should be worn when working on the starter to avoid injury to the eyes if, for some reason, the return spring should fly out.

Dismantling

Remove the starter from the engine.

502 50 18-01

Loosen the spring tension.

Dismantling

Remove the 4 bolts and lift off the starter.

The cylinder cover does not need to be loosened or detached.

Loosen the spring tension.

Pull out the starter cord about 30 cm. Brake the starter pulley with your thumb and lift the cord as illustrated.

Let the starter pulley rotate backwards slowly.

Remove the bolt in the centre of the starter pulley and remove the starter pulley.

Remove the bolt in the centre of the starter pulley. Lift the starter pulley carefully from the starter cover.

Page 5

Image 5

Husqvarna 343R, 345RX, 343F, 345FX, 345FXT manual 1Starter, Dismantling

Contents

Workshop manual English343R 345RX 343F 345FX 345FXT General recommendations ___________________ Model 343R, 345RX, 343F, 345FX, 345FXT Contents1.Starter __________________________________ 2.Electrical system _________________________Remember General recommendationsSpecial tools Fire risk1 Starter ContentsDismantling 1StarterDismantling Assembly AssemblyStarter Replacing the drive dogs Replacing the drive dogs1Starter Contents Electrical systemAssembly _________________________________ Checking the ignition spark ____________________Checking the ignition spark Electrical system502 71 Checking the ignition sparkElectrical system plug cover Replacing the spark502 50 Electrical systemElectrical system 502 54Dismantling DismantlingHeated handles Drive dogsDo not pry off the heating element before the locking catch has beenElectrical system Wiring diagramElectrical system Contents Fuel systemAssembly _________________________________ Carburettor settings _________________________Air filter Fuel systemAir filter Fuel filter Tank ventingMassage the oil into the air filter Fuel systemCarburettor Fuel pumpDismantling Fuel systemThe metering unit The carburettor’s designThe blending unit Fuel systemDismantling the carburettor The pump unitFuel system The pump unitIn the event of leakage – remove the needle valve Fuel systempositioned Note how the jets areFor example, the H-needleis a little shorter than the L-needleUse Loctite on the valve screws Assembling the carburettorFuel system Assembling the carburettorThe H-needleis a little shorter are not bent or pinched when thethan the L-needle Check carefully that the fuel hosesBasic setting Carburettor settingsFine adjustment FunctionCorrectly adjusted carburettor settingThe recommended max. speed must not be exceeded Idling speed T-screwadjustment 345RX/FX Carburettor adjustment 345RX/FXAdjusting the L-needle Adjusting the HFuel system Check for wear on pins A and BFuel system Disassemble the throttle control A, the lock to prevent accidental throttle operation B, the start throttle lock C and the throttle stop D in order to check if replacement is necessaryPage Contents 4 Centrifugal clutchAssembly _________________________________ Dismantling ________________________________502 21 Centrifugal clutchDismantling Dismantling502 54 Centrifugal clutch502 11 Clutch drumAssembly AssemblyCentrifugal clutch Change the bearings in the clutch housing if necessaryPage Contents 5 Angle gearAssembly _________________________________ Dismantling ________________________________Let the small circlip around the axle remain Angle gearDismantling DismantlingAngle gear 503 97Assembly 503 80 ShaftAngle gear ShaftContents 6 Cylinder and pistonCleaning, inspection _________________________ Assembly _________________________________Dismantling Cylinder and pistonDecompression valve Turn the valve the right way when fittingCylinder and piston Decompression valvemanifold is fitted using a Cleaning, inspectionInlet manifold Exercise caution if the inletInsufficient lubrication Analysis and actionsCause ActionCylinder and piston Piston scoring caused by heavy carbon depositsCause ActionPiston ring breakage Piston damage caused by a too high engine speedPiston ring guide pin Damage caused byCylinder and piston Foreign objectsCause ActionDefect Service tipsBe careful with the lower edge of the piston ring groove. If this is damaged, or if carbon depositsCylinder bore Wear tolerancesPiston ring gap Piston ring grooveContents 7 Crankshaft and crankcaseAssembly _________________________________ Leakage testing the crankcase _________________Dismantling Crankshaft and crankcaseDismantling 502 52 Crankshaft and crankcasecrankshaft Inspecting theCrankshaft and crankcase Inspecting theAssembly AssemblyCrankshaft and crankcase 502 50crankcase Leakage testing thePress down the sealing plates as far as possible between the boltsCrankshaft and crankcase Husqvarna E-Tech503 55 Page Contents ToolsStarter __________________________________ Electrical system __________________________505 38 List of toolsStarter Electricalgear List of toolsCrankshaft Workshop2003W24 114 01