Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna 966616701 Ignition Switch, Controls, For using “accessory”, turn the key clockwise

Models: PZ29D CE 966616701

1 72

Download 72 pages 31.14 Kb

Page 22

Image 22

CONTROLS

Ignition Switch

The ignition key is placed on the control panel and is used to start and stop the engine. Turn the key clockwise to start the engine.

Release the key to the RUN position when the engine has started.

For using “accessory”, turn the key clockwise.

8065-069

Ignition switch - RUN position

8065-070

Ignition switch - accessory

Page 22

Image 22

Husqvarna 966616701, PZ29D CE Ignition Switch, Controls, Release the key to the RUN position when the engine has started

Contents

PZ29D CE Operator ManualEnglish 2011 HTC. All rights reserved Orangeburg, SC CONTENTS Driving and Transport on Public RoadsPage General INTRODUCTIONCongratulations Driving and Transport on Public RoadsINTRODUCTION Good ServiceManufacturing Number Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx SYMBOLS AND DECALSIMPORTANT INFORMATION SYMBOLS AND DECALS SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH SAFETYSafety Instructions THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEETSAFETY Operate machine only in daylight or good artificial lightSlope Operation Personal Safety EquipmentSAFETY Children SAFETYThere is risk for burns if touched Safe Handling of Diesel FuelThe engine and the exhaust system become very hot during operation Allow engine and exhaust system to cool before refuelingUse protective glasses for maintenance work General MaintenanceSAFETY SAFETY Use protective gogglesTowing TransportSAFETY Do not operate this machine on public roadwaysSAFETY Rollover Protection System ROPSSpark Arrestor The engine and the exhaust system become very hot during operationCONTROLS Control LocationsCONTROLS Motion Control Levers1. Forward 2. Neutral 3. Neutral slot, Neutral lock 4. Reverse Blade switch Blade SwitchParking Brake CONTROLSTracking Knob Hour MeterCONTROLS For using “accessory”, turn the key clockwise Ignition SwitchRelease the key to the RUN position when the engine has started Ignition switch - RUN positionControl Module Battery VoltageCoolant Temperature Oil PressureCutting Height Pedals Seat AdjustmentsCONTROLS Pump Release Valves FusesFuel Shut Off Valve CONTROLSCONTROLS Fuel TanksRisk for burns if touched IMPORTANT INFORMATIONSteering OPERATIONTraining To move forward and backwardBefore Starting Roll Bar and Safety BeltThe seat belt must be used when the roll bar is in upright position OPERATIONStarting the Engine OPERATIONOPERATION 5. Disengage the mower blades by pressing the blade switch downBlade switch 7. Move the throttle to the middle positionTurn the key to RUN and observe glow plug light OPERATIONSet the engine speed The mower is equipped with a 12-volt negative Weak BatteryLead-acid batteries generate grounded system. The other vehicle must alsoRunning Make sure that no one is near mower when engaging blade switchOPERATION Operating on Hills OPERATIONStopping the Engine OPERATIONMowing Tips OPERATIONPump Release Valves No adjustments or maintenance should be carried out unlessMoving Machine By Hand IMPORTANT INFORMATION Tighten the valve moderatelyMAINTENANCE Engine and RadiatorTurn the ignition switch to OFF position and remove the key Before performing any service or adjustment checklistPlace the Blade-switch in the disengaged position Engage the parking brakeFor cleaning BatteryAlways wear eye protection when around batteries Battery Removal For replacingTire Pressures Safety SystemFuel Filter Only use O.E.M. specified tiresMAINTENANCE The machine must be standing still when applying the parking brakeParking Brake Adjustments Parking BrakeAlignment Drive Lever AdjustmentHeight Adjustment MAINTENANCEDeck Belt Removal Deck Belt InstallationDeck Belt MAINTENANCEReplacing Pump Belt Belt Removal/InstallationPump Belt MAINTENANCEV-belts ReinstallationClutch Belt RemovalDo not use lower grade hardware than specified Blade ReplacementCutting Blades MAINTENANCEMAINTENANCE Adjusting the Mower DeckLeveling Deck 1. Adjustment bolt 2. LocknutCaster Wheels Adjust anti-scalp rollers with the mower on a flat level surfaceRemoval and Installation Anti-scalp RollersHardware CleaningUse protective glasses when cleaning and washing MAINTENANCEGeneral LUBRICATIONLubrication Schedule Engine and RadiatorFront Wheel Bearings Wheel and Deck ZerksFront Wheel Mount Deck SpindleFluid and Filter Change Hydraulic DriveLUBRICATION Transmission Purging Procedures LUBRICATIONProblem TROUBLESHOOTING GUIDECause Cause TROUBLESHOOTING GUIDEProblem Engine overheatsWinter Storage ServiceSTORAGE a degreaser and warm waterWIRING DIAGRAM Hex Head Cap Screws TECHNICAL DATATorque Specifications U.S. Standard HardwareTransmission PZ29D CEEngine TECHNICAL DATA60 Flat Deck Dimension61 Combi Deck FrameUSA requirements CONFORMITY CERTIFICATESConformity Certificates For Model Listed Below EU Declaration of Conformity InformationSERVICE JOURNAL Delivery ServiceAfter 10 hours SERVICE JOURNALDaily Service SERVICE JOURNAL50-Hour Service SERVICE JOURNAL250-Hour Service SERVICE JOURNAL500-Hour Service SERVICE JOURNALAt Least Once Each Year SERVICE JOURNALAction SERVICE JOURNALDate, mtr reading, stamp, sign Page Original Instructions 115 404727 Rev B2011-11-30