Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna PZ29D CE, 966616701 Drive Lever Adjustment, Height Adjustment, Alignment, Maintenance

Models: PZ29D CE 966616701

1 72

Download 72 pages 31.14 Kb

Page 43

Image 43

MAINTENANCE

Drive Lever Adjustment

Drive levers can be adjusted up and down and side to side to suit the operator.

Height Adjustment

Alignment adjustments will be needed after adjusting the height. Make adjustments with the unit turned off.

1.Remove the bolts securing the drive levers to the control assembly.

2.Position the drive lever at the desired height and reinstall the bolts, but do not fully tighten the bolts at this time.

Alignment

To align the drive levers uniformly, rotate both drive levers inward and press both levers all of the way forward.

1.Rotate the drive levers in the upper slots of the lever until the levers are aligned with each other. Tighten bolts on each drive lever securely.

8065-049

1.Drive levers

2.Control assembly

3.Alignment slot Neutral adjustment

Page 43

Image 43

Husqvarna PZ29D CE, 966616701 manual Drive Lever Adjustment, Height Adjustment, Alignment, Maintenance

Contents

PZ29D CE Operator ManualEnglish 2011 HTC. All rights reserved Orangeburg, SC Driving and Transport on Public Roads CONTENTSPage Driving and Transport on Public Roads INTRODUCTIONCongratulations GeneralINTRODUCTION Good ServiceManufacturing Number Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx SYMBOLS AND DECALSIMPORTANT INFORMATION SYMBOLS AND DECALS THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET SAFETYSafety Instructions SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATHOperate machine only in daylight or good artificial light SAFETYSlope Operation Personal Safety EquipmentSAFETY SAFETY ChildrenAllow engine and exhaust system to cool before refueling Safe Handling of Diesel FuelThe engine and the exhaust system become very hot during operation There is risk for burns if touchedUse protective glasses for maintenance work General MaintenanceSAFETY Use protective goggles SAFETYDo not operate this machine on public roadways TransportSAFETY TowingThe engine and the exhaust system become very hot during operation Rollover Protection System ROPSSpark Arrestor SAFETYControl Locations CONTROLSCONTROLS Motion Control Levers1. Forward 2. Neutral 3. Neutral slot, Neutral lock 4. Reverse CONTROLS Blade SwitchParking Brake Blade switchTracking Knob Hour MeterCONTROLS Ignition switch - RUN position Ignition SwitchRelease the key to the RUN position when the engine has started For using “accessory”, turn the key clockwiseOil Pressure Battery VoltageCoolant Temperature Control ModuleCutting Height Pedals Seat AdjustmentsCONTROLS CONTROLS FusesFuel Shut Off Valve Pump Release ValvesIMPORTANT INFORMATION Fuel TanksRisk for burns if touched CONTROLSTo move forward and backward OPERATIONTraining SteeringOPERATION Roll Bar and Safety BeltThe seat belt must be used when the roll bar is in upright position Before StartingOPERATION Starting the Engine7. Move the throttle to the middle position 5. Disengage the mower blades by pressing the blade switch downBlade switch OPERATIONTurn the key to RUN and observe glow plug light OPERATIONSet the engine speed grounded system. The other vehicle must also Weak BatteryLead-acid batteries generate The mower is equipped with a 12-volt negativeRunning Make sure that no one is near mower when engaging blade switchOPERATION OPERATION Operating on HillsOPERATION Stopping the EngineOPERATION Mowing TipsIMPORTANT INFORMATION Tighten the valve moderately No adjustments or maintenance should be carried out unlessMoving Machine By Hand Pump Release ValvesEngine and Radiator MAINTENANCEEngage the parking brake Before performing any service or adjustment checklistPlace the Blade-switch in the disengaged position Turn the ignition switch to OFF position and remove the keyFor replacing BatteryAlways wear eye protection when around batteries Battery Removal For cleaningOnly use O.E.M. specified tires Safety SystemFuel Filter Tire PressuresParking Brake The machine must be standing still when applying the parking brakeParking Brake Adjustments MAINTENANCEMAINTENANCE Drive Lever AdjustmentHeight Adjustment AlignmentMAINTENANCE Deck Belt InstallationDeck Belt Deck Belt RemovalMAINTENANCE Belt Removal/InstallationPump Belt Replacing Pump BeltRemoval ReinstallationClutch Belt V-beltsMAINTENANCE Blade ReplacementCutting Blades Do not use lower grade hardware than specified1. Adjustment bolt 2. Locknut Adjusting the Mower DeckLeveling Deck MAINTENANCEAnti-scalp Rollers Adjust anti-scalp rollers with the mower on a flat level surfaceRemoval and Installation Caster WheelsMAINTENANCE CleaningUse protective glasses when cleaning and washing HardwareEngine and Radiator LUBRICATIONLubrication Schedule GeneralDeck Spindle Wheel and Deck ZerksFront Wheel Mount Front Wheel BearingsFluid and Filter Change Hydraulic DriveLUBRICATION LUBRICATION Transmission Purging ProceduresProblem TROUBLESHOOTING GUIDECause Engine overheats TROUBLESHOOTING GUIDEProblem Causea degreaser and warm water ServiceSTORAGE Winter StorageWIRING DIAGRAM U.S. Standard Hardware TECHNICAL DATATorque Specifications Hex Head Cap ScrewsTECHNICAL DATA PZ29D CEEngine TransmissionFrame Dimension61 Combi Deck 60 Flat DeckEU Declaration of Conformity Information CONFORMITY CERTIFICATESConformity Certificates For Model Listed Below USA requirementsDelivery Service SERVICE JOURNALSERVICE JOURNAL After 10 hoursSERVICE JOURNAL Daily ServiceSERVICE JOURNAL 50-Hour ServiceSERVICE JOURNAL 250-Hour ServiceSERVICE JOURNAL 500-Hour ServiceSERVICE JOURNAL At Least Once Each YearAction SERVICE JOURNALDate, mtr reading, stamp, sign Page Original Instructions 115 404727 Rev B2011-11-30