Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna 966616701 manual Operation, Disengage the mower blades by pressing the blade switch down

Models: PZ29D CE 966616701

1 72

Download 72 pages 31.14 Kb

Page 30

Image 30

OPERATION

5.Disengage the mower blades by pressing the blade switch down.

6.Move the steering controls outward to the locked (outer) neutral position.

7. Move the throttle to the middle position.

8065-067

Blade switch

8065-108

Place controls in neutral position

8065-071

Set the throttle

Page 30

Image 30

Husqvarna 966616701, PZ29D CE manual Operation, Disengage the mower blades by pressing the blade switch down, Blade switch

Contents

Operator Manual PZ29D CEEnglish 2011 HTC. All rights reserved Orangeburg, SC CONTENTS Driving and Transport on Public RoadsPage General INTRODUCTIONCongratulations Driving and Transport on Public RoadsGood Service INTRODUCTIONManufacturing Number SYMBOLS AND DECALS Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxxIMPORTANT INFORMATION SYMBOLS AND DECALS SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH SAFETYSafety Instructions THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEETSAFETY Operate machine only in daylight or good artificial lightPersonal Safety Equipment Slope OperationSAFETY Children SAFETYThere is risk for burns if touched Safe Handling of Diesel FuelThe engine and the exhaust system become very hot during operation Allow engine and exhaust system to cool before refuelingGeneral Maintenance Use protective glasses for maintenance workSAFETY SAFETY Use protective gogglesTowing TransportSAFETY Do not operate this machine on public roadwaysSAFETY Rollover Protection System ROPSSpark Arrestor The engine and the exhaust system become very hot during operationCONTROLS Control LocationsMotion Control Levers CONTROLS1. Forward 2. Neutral 3. Neutral slot, Neutral lock 4. Reverse Blade switch Blade SwitchParking Brake CONTROLSHour Meter Tracking KnobCONTROLS For using “accessory”, turn the key clockwise Ignition SwitchRelease the key to the RUN position when the engine has started Ignition switch - RUN positionControl Module Battery VoltageCoolant Temperature Oil PressureSeat Adjustments Cutting Height PedalsCONTROLS Pump Release Valves FusesFuel Shut Off Valve CONTROLSCONTROLS Fuel TanksRisk for burns if touched IMPORTANT INFORMATIONSteering OPERATIONTraining To move forward and backwardBefore Starting Roll Bar and Safety BeltThe seat belt must be used when the roll bar is in upright position OPERATIONStarting the Engine OPERATIONOPERATION 5. Disengage the mower blades by pressing the blade switch downBlade switch 7. Move the throttle to the middle positionOPERATION Turn the key to RUN and observe glow plug lightSet the engine speed The mower is equipped with a 12-volt negative Weak BatteryLead-acid batteries generate grounded system. The other vehicle must alsoMake sure that no one is near mower when engaging blade switch RunningOPERATION Operating on Hills OPERATIONStopping the Engine OPERATIONMowing Tips OPERATIONPump Release Valves No adjustments or maintenance should be carried out unlessMoving Machine By Hand IMPORTANT INFORMATION Tighten the valve moderatelyMAINTENANCE Engine and RadiatorTurn the ignition switch to OFF position and remove the key Before performing any service or adjustment checklistPlace the Blade-switch in the disengaged position Engage the parking brakeFor cleaning BatteryAlways wear eye protection when around batteries Battery Removal For replacingTire Pressures Safety SystemFuel Filter Only use O.E.M. specified tiresMAINTENANCE The machine must be standing still when applying the parking brakeParking Brake Adjustments Parking BrakeAlignment Drive Lever AdjustmentHeight Adjustment MAINTENANCEDeck Belt Removal Deck Belt InstallationDeck Belt MAINTENANCEReplacing Pump Belt Belt Removal/InstallationPump Belt MAINTENANCEV-belts ReinstallationClutch Belt RemovalDo not use lower grade hardware than specified Blade ReplacementCutting Blades MAINTENANCEMAINTENANCE Adjusting the Mower DeckLeveling Deck 1. Adjustment bolt 2. LocknutCaster Wheels Adjust anti-scalp rollers with the mower on a flat level surfaceRemoval and Installation Anti-scalp RollersHardware CleaningUse protective glasses when cleaning and washing MAINTENANCEGeneral LUBRICATIONLubrication Schedule Engine and RadiatorFront Wheel Bearings Wheel and Deck ZerksFront Wheel Mount Deck SpindleHydraulic Drive Fluid and Filter ChangeLUBRICATION Transmission Purging Procedures LUBRICATIONTROUBLESHOOTING GUIDE ProblemCause Cause TROUBLESHOOTING GUIDEProblem Engine overheatsWinter Storage ServiceSTORAGE a degreaser and warm waterWIRING DIAGRAM Hex Head Cap Screws TECHNICAL DATATorque Specifications U.S. Standard HardwareTransmission PZ29D CEEngine TECHNICAL DATA60 Flat Deck Dimension61 Combi Deck FrameUSA requirements CONFORMITY CERTIFICATESConformity Certificates For Model Listed Below EU Declaration of Conformity InformationSERVICE JOURNAL Delivery ServiceAfter 10 hours SERVICE JOURNALDaily Service SERVICE JOURNAL50-Hour Service SERVICE JOURNAL250-Hour Service SERVICE JOURNAL500-Hour Service SERVICE JOURNALAt Least Once Each Year SERVICE JOURNALSERVICE JOURNAL ActionDate, mtr reading, stamp, sign Page 115 404727 Rev B Original Instructions2011-11-30