Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna 966616701, PZ29D CE manual Hour Service, Service Journal

Models: PZ29D CE 966616701

1 72

Download 72 pages 31.14 Kb

Page 68

Image 68

SERVICE JOURNAL

Action

Date, mtr reading, stamp, sign

500-Hour Service
Grease fittings (caster pivots and caster wheels)	¨
Inspect dampers	¨
Inspect frame	¨
Inspect throttle cable	¨
Inspect hardware	¨
Check the tire pressures	¨
Change the engine oil and filter	¨
Change air filter	¨
Inspect fuel filter	¨
Check engine RPM	¨
Clean underside of deck	¨
Check blade pitch	¨
Grease blade spindles	¨
Inspect spindle bearings	¨
Inspect deck belt and blades	¨
Inspect idler arm bearings	¨
Inspect deck idler pulleys	¨
Change hydraulic oil and filter	¨
Change anti-freeze	¨
Replace hydraulic drive belt	¨
Inspect hydraulic hoses	¨
Check neutral position	¨
Inspect battery connections	¨
Load test battery	¨
Clean electrical connections	¨
Inspect the clutch	¨
Check safety system	¨
Check seat belt	¨
Check ROPS	¨
Check fuel system for leaks	¨
Inspect safety guards and shields	¨
Check brake adjustment	¨
Change alternator belt	¨

Page 68

Image 68

Husqvarna 966616701, PZ29D CE manual Hour Service, Service Journal

Contents

English Operator ManualPZ29D CE 2011 HTC. All rights reserved Orangeburg, SC CONTENTS Driving and Transport on Public RoadsPage INTRODUCTION CongratulationsGeneral Driving and Transport on Public RoadsManufacturing Number Good ServiceINTRODUCTION IMPORTANT INFORMATION SYMBOLS AND DECALSXxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx SYMBOLS AND DECALS SAFETY Safety InstructionsSAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEETSAFETY Operate machine only in daylight or good artificial lightSAFETY Personal Safety EquipmentSlope Operation Children SAFETYSafe Handling of Diesel Fuel The engine and the exhaust system become very hot during operationThere is risk for burns if touched Allow engine and exhaust system to cool before refuelingSAFETY General MaintenanceUse protective glasses for maintenance work SAFETY Use protective gogglesTransport SAFETYTowing Do not operate this machine on public roadwaysRollover Protection System ROPS Spark ArrestorSAFETY The engine and the exhaust system become very hot during operationCONTROLS Control Locations1. Forward 2. Neutral 3. Neutral slot, Neutral lock 4. Reverse Motion Control LeversCONTROLS Blade Switch Parking BrakeBlade switch CONTROLSCONTROLS Hour MeterTracking Knob Ignition Switch Release the key to the RUN position when the engine has startedFor using “accessory”, turn the key clockwise Ignition switch - RUN positionBattery Voltage Control ModuleOil Pressure Coolant TemperatureCONTROLS Seat AdjustmentsCutting Height Pedals Fuses Fuel Shut Off ValvePump Release Valves CONTROLSFuel Tanks Risk for burns if touchedCONTROLS IMPORTANT INFORMATIONOPERATION TrainingSteering To move forward and backwardRoll Bar and Safety Belt The seat belt must be used when the roll bar is in upright positionBefore Starting OPERATIONStarting the Engine OPERATION5. Disengage the mower blades by pressing the blade switch down Blade switchOPERATION 7. Move the throttle to the middle positionSet the engine speed OPERATIONTurn the key to RUN and observe glow plug light Weak Battery Lead-acid batteries generateThe mower is equipped with a 12-volt negative grounded system. The other vehicle must alsoOPERATION Make sure that no one is near mower when engaging blade switchRunning Operating on Hills OPERATIONStopping the Engine OPERATIONMowing Tips OPERATIONNo adjustments or maintenance should be carried out unless Moving Machine By HandPump Release Valves IMPORTANT INFORMATION Tighten the valve moderatelyMAINTENANCE Engine and RadiatorBefore performing any service or adjustment checklist Place the Blade-switch in the disengaged positionTurn the ignition switch to OFF position and remove the key Engage the parking brakeBattery Always wear eye protection when around batteries Battery RemovalFor cleaning For replacingSafety System Fuel FilterTire Pressures Only use O.E.M. specified tiresThe machine must be standing still when applying the parking brake Parking Brake AdjustmentsMAINTENANCE Parking BrakeDrive Lever Adjustment Height AdjustmentAlignment MAINTENANCEDeck Belt Installation Deck BeltDeck Belt Removal MAINTENANCEBelt Removal/Installation Pump BeltReplacing Pump Belt MAINTENANCEReinstallation Clutch BeltV-belts RemovalBlade Replacement Cutting BladesDo not use lower grade hardware than specified MAINTENANCEAdjusting the Mower Deck Leveling DeckMAINTENANCE 1. Adjustment bolt 2. LocknutAdjust anti-scalp rollers with the mower on a flat level surface Removal and InstallationCaster Wheels Anti-scalp RollersCleaning Use protective glasses when cleaning and washingHardware MAINTENANCELUBRICATION Lubrication ScheduleGeneral Engine and RadiatorWheel and Deck Zerks Front Wheel MountFront Wheel Bearings Deck SpindleLUBRICATION Hydraulic DriveFluid and Filter Change Transmission Purging Procedures LUBRICATIONCause TROUBLESHOOTING GUIDEProblem TROUBLESHOOTING GUIDE ProblemCause Engine overheatsService STORAGEWinter Storage a degreaser and warm waterWIRING DIAGRAM TECHNICAL DATA Torque SpecificationsHex Head Cap Screws U.S. Standard HardwarePZ29D CE EngineTransmission TECHNICAL DATADimension 61 Combi Deck60 Flat Deck FrameCONFORMITY CERTIFICATES Conformity Certificates For Model Listed BelowUSA requirements EU Declaration of Conformity InformationSERVICE JOURNAL Delivery ServiceAfter 10 hours SERVICE JOURNALDaily Service SERVICE JOURNAL50-Hour Service SERVICE JOURNAL250-Hour Service SERVICE JOURNAL500-Hour Service SERVICE JOURNALAt Least Once Each Year SERVICE JOURNALDate, mtr reading, stamp, sign SERVICE JOURNALAction Page 2011-11-30 115 404727 Rev BOriginal Instructions