Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna PZ29D CE manual Moving Machine By Hand, Pump Release Valves, the parking brake activated

Models: PZ29D CE 966616701

1 72

Download 72 pages 31.14 Kb

Page 37

Image 37

OPERATION

Moving Machine By Hand

Pump Release Valves

Pump release valves are located on the right side of each pump. They are used to release the system so the machine can be moved by hand when not running. Tilt the seat forward to access the pumps.

Use a 5/8" wrench or socket and ratchet. Turn each pump release valve ½ turn. Reverse the procedure to reset the pumps.

IMPORTANT INFORMATION Tighten the valve moderately.

Do not overtighten the valve when closing. That can damage the valve seat.

8065-076

Release valves

WARNING!

No adjustments or maintenance should be carried out unless:

•the engine stopped

•the ignition key removed

•the parking brake activated

Page 37

Image 37

Husqvarna PZ29D CE manual Moving Machine By Hand, Pump Release Valves, IMPORTANT INFORMATION Tighten the valve moderately

Contents

PZ29D CE Operator ManualEnglish 2011 HTC. All rights reserved Orangeburg, SC Driving and Transport on Public Roads CONTENTSPage Congratulations INTRODUCTIONGeneral Driving and Transport on Public RoadsINTRODUCTION Good ServiceManufacturing Number Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx SYMBOLS AND DECALSIMPORTANT INFORMATION SYMBOLS AND DECALS Safety Instructions SAFETYSAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEETOperate machine only in daylight or good artificial light SAFETYSlope Operation Personal Safety EquipmentSAFETY SAFETY ChildrenThe engine and the exhaust system become very hot during operation Safe Handling of Diesel FuelThere is risk for burns if touched Allow engine and exhaust system to cool before refuelingUse protective glasses for maintenance work General MaintenanceSAFETY Use protective goggles SAFETYSAFETY TransportTowing Do not operate this machine on public roadwaysSpark Arrestor Rollover Protection System ROPSSAFETY The engine and the exhaust system become very hot during operationControl Locations CONTROLSCONTROLS Motion Control Levers1. Forward 2. Neutral 3. Neutral slot, Neutral lock 4. Reverse Parking Brake Blade SwitchBlade switch CONTROLSTracking Knob Hour MeterCONTROLS Release the key to the RUN position when the engine has started Ignition SwitchFor using “accessory”, turn the key clockwise Ignition switch - RUN positionCoolant Temperature Battery VoltageControl Module Oil PressureCutting Height Pedals Seat AdjustmentsCONTROLS Fuel Shut Off Valve FusesPump Release Valves CONTROLSRisk for burns if touched Fuel TanksCONTROLS IMPORTANT INFORMATIONTraining OPERATIONSteering To move forward and backwardThe seat belt must be used when the roll bar is in upright position Roll Bar and Safety BeltBefore Starting OPERATIONOPERATION Starting the EngineBlade switch 5. Disengage the mower blades by pressing the blade switch downOPERATION 7. Move the throttle to the middle positionTurn the key to RUN and observe glow plug light OPERATIONSet the engine speed Lead-acid batteries generate Weak BatteryThe mower is equipped with a 12-volt negative grounded system. The other vehicle must alsoRunning Make sure that no one is near mower when engaging blade switchOPERATION OPERATION Operating on HillsOPERATION Stopping the EngineOPERATION Mowing TipsMoving Machine By Hand No adjustments or maintenance should be carried out unlessPump Release Valves IMPORTANT INFORMATION Tighten the valve moderatelyEngine and Radiator MAINTENANCEPlace the Blade-switch in the disengaged position Before performing any service or adjustment checklistTurn the ignition switch to OFF position and remove the key Engage the parking brakeAlways wear eye protection when around batteries Battery Removal BatteryFor cleaning For replacingFuel Filter Safety SystemTire Pressures Only use O.E.M. specified tiresParking Brake Adjustments The machine must be standing still when applying the parking brakeMAINTENANCE Parking BrakeHeight Adjustment Drive Lever AdjustmentAlignment MAINTENANCEDeck Belt Deck Belt InstallationDeck Belt Removal MAINTENANCEPump Belt Belt Removal/InstallationReplacing Pump Belt MAINTENANCEClutch Belt ReinstallationV-belts RemovalCutting Blades Blade ReplacementDo not use lower grade hardware than specified MAINTENANCELeveling Deck Adjusting the Mower DeckMAINTENANCE 1. Adjustment bolt 2. LocknutRemoval and Installation Adjust anti-scalp rollers with the mower on a flat level surfaceCaster Wheels Anti-scalp RollersUse protective glasses when cleaning and washing CleaningHardware MAINTENANCELubrication Schedule LUBRICATIONGeneral Engine and RadiatorFront Wheel Mount Wheel and Deck ZerksFront Wheel Bearings Deck SpindleFluid and Filter Change Hydraulic DriveLUBRICATION LUBRICATION Transmission Purging ProceduresProblem TROUBLESHOOTING GUIDECause Problem TROUBLESHOOTING GUIDECause Engine overheatsSTORAGE ServiceWinter Storage a degreaser and warm waterWIRING DIAGRAM Torque Specifications TECHNICAL DATAHex Head Cap Screws U.S. Standard HardwareEngine PZ29D CETransmission TECHNICAL DATA61 Combi Deck Dimension60 Flat Deck FrameConformity Certificates For Model Listed Below CONFORMITY CERTIFICATESUSA requirements EU Declaration of Conformity InformationDelivery Service SERVICE JOURNALSERVICE JOURNAL After 10 hoursSERVICE JOURNAL Daily ServiceSERVICE JOURNAL 50-Hour ServiceSERVICE JOURNAL 250-Hour ServiceSERVICE JOURNAL 500-Hour ServiceSERVICE JOURNAL At Least Once Each YearAction SERVICE JOURNALDate, mtr reading, stamp, sign Page Original Instructions 115 404727 Rev B2011-11-30