Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna LZ5227, LZ6130 manual Battery, Always use protective glasses when handling the battery

Models: LZ30, LZ30C LZ5227, LZ6130 LZ6130C, LZ7230C LZ7230, LZ6127

1 77

Download 77 pages 3.95 Kb

Page 38

Battery

MAINTENANCE

Battery

Your mower is equipped with a maintenance free battery and does not need servicing. However, periodic charging of the battery with an automotive type battery charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Recharge at 6-10 amperes for 1 hour

To clean battery and terminals

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

1.Lift the seat and rotate forward.

2.Remove the red terminal guard

3.Disconnect BLACK battery cable ﬁrst, then the RED battery cable and remove the battery from the machine.

4.Rinse the battery with plain water and dry.

5.Clean terminals and battery cable ends with wire brush until shiny.

6.Coat terminals with grease or petroleum jelly.

7.Reinstall battery.

Replacing battery

1.Lift seat and rotate forward.

2.Remove the red terminal guard.

3.Using two ½" wrenches disconnect BLACK battery cable then RED battery cable.

4.Remove the knobs and the battery hold downs.

5.Carefully remove the battery from the mower.

6.Install new battery with terminals in the same position as the old battery.

7.Reinstall the battery hold downs.

8.First connect RED battery cable to positive (+) battery terminal with hex bolt and hex nut.

9.Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and hex nut.

10.Tighten securely.

11.Replace the red terminal guard

12.Lower seat.

English-38

Always use protective glasses when handling the battery.

IMPORTANT INFORMATION

Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

Always use two wrenches for the terminal screws.

WARNING!

Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected ﬁrst to prevent sparks from accidental grounding.

1	2
	2
	8011-466

1.Terminal guard

2.Battery hold downs Battery installation

Image 38

Husqvarna LZ5227, LZ6130, LZ7230, LZ6127 Battery, Always use protective glasses when handling the battery, Maintenance

Contents

Operator Manual EnglishPage Driving and Transport on Public Roads CONTENTSTROUBLESHOOTING GUIDE English-4 General INTRODUCTIONCongratulations Driving and Transport on Public RoadsPlease have these available when ordering spare parts Good ServiceManufacturing Number INTRODUCTIONIMPORTANT INFORMATION Xxxx xxxxxx xxxxx SYMBOLS AND DECALSXxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxremove key before SYMBOLS AND DECALSremove safety ManualGeneral Operation SAFETYSafety Instructions SAFETY Operate machine only in daylight or good artiﬁcial lightSAFETY Personal Safety EquipmentSlope Operation SAFETY ChildrenSAFETY The engine and the exhaust system, become very hot during operationRisk for burns if touched Safe Handling of GasolineSAFETY General MaintenanceUse protective glasses for maintenance work English-15 SAFETYRisk of sparking IMPORTANT INFORMATION TransportCustomer responsibilities SAFETYSAFETY Roll over Protection system ROPSSpark Arresters English-17CONTROLS Controls1. Forward 2. Neutral 3. Neutral slot, Neutral lock 4. Reverse Motion Control LeversCONTROLS Parking Brake Hour meterTracking knob CONTROLSFuses Blade switchIgnition Switch CONTROLSThe engine and the exhaust system, become very hot during operation RefuelingCONTROLS Risk for burns if touchedFuel shut off valve Seat adjustment leverSeat Lock Lengthways adjustmentLifting Lever for the Mower Deck Choke controlThrottle control CONTROLSPump release valves AccessoriesCutting height lift pedal Only rotate the valve ¼ to ½ turn to release the systemTraining OPERATIONOperation SteeringBefore Starting Roll bar and safety beltThe seat belt must be used when the roll bar is in upright position Starting the EngineSteering controls in the outward, locked neutral position OPERATIONDepress the control for disengaging the mower deck Set the throttleOpen the fuel valve OPERATIONSet the choke control Turn to the start positionMOWING no choke OPERATIONIMPORTANT INFORMATION IMPORTANT INFORMATION To start an engine with a weak batteryOPERATION To attach jumper cablesRunning The mower deck’s gauge wheels should be evenly adjustedEnsure that no one is near mower when engaging blade switch OPERATIONIMPORTANT INFORMATION Operating on hillsOPERATION Mowing Tips OPERATIONMoving by Hand No adjustments or maintenance to be carried out unlessStopping the Engine the engine stopped the ignition key removedMAINTENANCE MAINTENANCE English-37Always use two wrenches for the terminal screws BatteryAlways use protective glasses when handling the battery MAINTENANCEFitting the wrong spark plug type can damage the engine Safety SystemIgnition System MAINTENANCEStart motor MAINTENANCESafety system WorksChoke Cable Engine Cooling Air IntakeThrottle Cable MAINTENANCEFilter should be assembled dry and not be oiled Do not use compressed air to clean the air ﬁlterAir Filter MAINTENANCEIMPORTANT INFORMATION Engine Oil CoolerMAINTENANCE MAINTENANCE Fuel FilterFuel Pump Air Filter MAINTENANCE Checking the V-beltsDeck belt To replace deck beltChecking Tire Pressures Faulty adjustment of the parking brake can cause an accidentPump belt Checking the Parking BrakeDo not use a lower grade hardware than speciﬁed Blade replacementChecking the Blades MAINTENANCEBefore performing any service or adjustment checklist Adjusting the Mower DeckAdjusting Cutting Height 2. Place the Blade switch in the disengaged positionCaster Wheels Cleaning and WashingUse protective glasses when cleaning and washing HardwareGeneral LUBRICATIONLubrication Schedule Lubricating with the Lubrication Schedule Lubricating the CablesShaft Bushings and Linkage LUBRICATIONIMPORTANT INFORMATION Avoid skin contact wash with soap and water in case of spillsLUBRICATION IMPORTANT INFORMATIONIMPORTANT INFORMATION Checking the Oil LevelLUBRICATION LUBRICATION Oil RecommendationsOil Type IMPORTANT INFORMATIONLUBRICATION Mower Deck Height AdjusterLubricating the cutting height adjuster Throttle and Choke Cables, Lever BearingsMower Deck Struts LUBRICATIONSteering Control Shafts Changing the Oil FilterCause TROUBLESHOOTING GUIDEProblem TROUBLESHOOTING GUIDE English-58Winter Storage ServiceSTORAGE For Serial No. 074439861 and after WIRING DIAGRAMSFor unit produced before Serial No English-60LZ6127 TECHNICAL DATALZ5227 EngineTECHNICAL DATA English-62TECHNICAL DATA English-63TECHNICAL DATA English-64TECHNICAL DATA English-65Accessories Torque SpeciﬁcationsTECHNICAL DATA Head lights BioClip attachment Mulch clip Collection systemCE requirements CONFORMITY CERTIFICATESConformity Certiﬁcates USA requirements Delivery Service SERVICE JOURNALService Journal 1. Change engine oil After the First 5-8 HoursSERVICE JOURNAL English-693. Check the tire pressures 4. Check battery with cables 25-Hour ServiceSERVICE JOURNAL 5. Lubricate according to lubrication chart1. Perform the 25-hour service 50-Hour ServiceSERVICE JOURNAL 3. Change engine oil 4. Lubricate according to lubrication chart1. Perform the 25-hour service 2. Perform the 50-hour service 100-Hour ServiceSERVICE JOURNAL 3. Change the engine oil ﬁlter 4. Clean/replace the spark plugs300-Hour Service SERVICE JOURNALAt Least Once Each Year SERVICE JOURNALSERVICE JOURNAL English-75SECTION 2 HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY WARRANTY STATEMENTSECTION 1 LIMITED WARRANTY SECTION 6 PROCEDURE TO OBTAIN WARRANTY CONSIDERATION539 131254 R01 08/23/07