Manuals / Husqvarna / Lawn and Garden / Brush Cutter

Husqvarna SG13A, SG13 manual Cleaning the cyclone filter, Maintenance, Important Information

Models: SG13/968999353 SG13A, SG13

1 50

Download 50 pages 16.43 Kb

Page 32

Cleaning the cyclone filter

MAINTENANCE

Cleaning the cyclone filter

The cyclone filter collects the largest contaminant particles, which collect in the container. When you can see a layer of dirt at the bottom of the container, the cyclone housing (4), air channels and air intake screen (3) must be cleaned.

Remove the three screw holding the cyclone housing. Remove the housing with the air intake screen and remove the air channels.

The air channels may remain in the upper portion or follow along with the housing when removed.

8011-188

8011-213

Clean the components. Use water, detergent and a washing-up brush. Dry carefully.

IMPORTANT INFORMATION

Exercise care when reassembling to avoid damaging anything.

Make sure when mounting that the air intake screen fits exactly in its guide in the upper portion.

Make sure the air channel ends up in the proper position.

Refit the components. Place the air channels in the cyclone housing. Insert cyclone housing into position and make sure it fits in the upper portion. DO NOT use force; rather coax it into place before fitting the screws.

8011-212

8011-213

32

Image 32

Husqvarna SG13A, SG13 Cleaning the cyclone filter, Exercise care when reassembling to avoid damaging anything, Maintenance

Contents

SG13A/CE/968999239 SG13/968999353MANUAL NO. 539109280 REV. 03 12/01/05 Operator’s Manual2005 Husqvarna All Rights Reserved Printed Beatrice, Nebraska TABLE OF CONTENTS Stump Grinder SG13A Symbols and decalsSafety instructions MaintenanceGood service INTRODUCTIONCongratulations Insure your machineIMPORTANT INFORMATION SYMBOLS AND DECALSDecals and machine-bound instructions Location of decals Translation of instructionsDecal Important information DecalIMPORTANT INFORMATION SAFETY INSTRUCTIONSGeneral use IMPORTANT INFORMATION SAFETY INSTRUCTIONSNever leave the machine unsupervised with the engine running Preparations SAFETY INSTRUCTIONSClear the work area before beginning work Use appropriate equipmentOperating SAFETY INSTRUCTIONSMovement/Transport StorageChildren SAFETY INSTRUCTIONSFuel system SAFETY INSTRUCTIONSSAFETY INSTRUCTIONS MaintenanceTurn off the engine and remove the spark plug cable PROTECTIVE EQUIPMENT Personal equipmentSET-UP Equipment set-up9. Remove air cleaner and double wire clamp from engine. Figure SET-UP18. Reattach air cleaner to engine SET-UPMain components and operating controls CONTROLSPresentation CONTROLS EngineThrottle Starter Starter handleFuel valve Choke controlSpark plug MufflerOil dipstick Oil drainageDo not bind the bar to the handle It is there for your safety Fuel tankFueling Centrifugal clutchOn/Off Engine switch on the panel Adjustment bar for the handleBrake NEVER operate a machine with a defective brakeEngine switch on the engine OPERATIONStarting the engine Fuel valveEngine switch on the handle Dead man’s grip barStarter handle OPERATIONEngine switch Normal shutdownShutdown in emergency situations BrakeBefore you start OPERATIONUsing your stump grinder DISENGAGE 4. Set engine switch on handlebar to ONOPERATION 1. Place the cutting blade near the top front edge of the tree stumpIMPORTANT INFORMATION OPERATION5. Tilt the machine on its wheels, lifting the cutting 18. Shut off the machine when you are done Operating on hillsTransport OPERATIONMAINTENANCE Maintenance scheduleNo service operations may be performed on the engine or unit unless The machine is securely parked where it will not tip or begin rollingCleaning the cyclone filter Exercise care when reassembling to avoid damaging anythingMake sure the air channel ends up in the proper position MAINTENANCEReplacing the air filter DO NOT wash the paper filter. DO NOT oil the paper filterMAINTENANCE IMPORTANT INFORMATIONCleaning the sludge reservoir Idle adjustmentRisk for carbon monoxide poisoning. Perform the adjustment outdoors MAINTENANCEIgnition system Fitting the wrong spark plug type can damage the engineMAINTENANCE IMPORTANT INFORMATIONAdjusting the drive belt MAINTENANCEDisassembling and reassembling the blade, pockets and teeth L = Left mounting R = Right mountingEnsure that the tooth cutters are turned in the cutting direction MAINTENANCERemoving and refitting the wheels MAINTENANCEAdjusting the brake Cleaning and washingTwo minute rule MAINTENANCELUBRICATION 8011-276chg1. Engine oil Checking the engine’s oil levelLUBRICATION IMPORTANT INFORMATIONLUBRICATION 2. Right wheel3. Throttle cable TROUBLESHOOTING SymptomCause ActionProblem Possible solutionsTROUBLESHOOTING Clutch is worn - replace shoes and springs, and/or clutch bearingsWinter storage ServiceSTORAGE TECHNICAL DATA SPECIFICATIONSModel SG13AWIRING DIAGRAM SERVICE JOURNAL Delivery serviceDate, stamp, signature SERVICE JOURNALAction