Bin Application, Ice Machine Specifications | Ice-O-Matic GEM0956R

GEM0650/0956/1256 Remote

For the Installer

Bin Application

The Pearl Ice™ Series are designed to fit the following Ice-O-Matic Bins ●B42, using Bin Top KBT 24 (Note: GEM0650 and GEM0956 ONLY) ●B25, B40 B55 using Bin Top KBT 19.

●B100 using Bin Top KBT 23 (one unit) or KBT 22 (two units). ●B120, B150, B170 Not designed for Pearl Ice™ Series.

Dispenser Application

The Pearl Ice™ Series can be placed on and used with certain ice and beverage dispensers. Kits are required for proper operation.

IOM Pearl Ice™ Accessory List

Dispenser	GEM0650	GEM0956
Ice-O-Matic IOD150	KBT15022, KGEMDIV	KBT15022, KGEMDIV

Ice-O-Matic IOD200 or	KBT25022, KGEMBIOD	KBT25022, KGEMBIOD
IOD250
Cornelius ED or DF150	KBT15022,	KBT15022,
	R629088514(Cornelius	R629088514(Cornelius
	Model)	Model)

Cornelius ED or DF200	KBT25022, KGEM200	KBT25022, KGEM200

Cornelius ED or DF250	KBT25022, KGEM250	KBT25022, KGEM250

Lancer Nugget Ready	N/A	N/A
Flavor Select
SerVend S-200, SV200, S-	N/A	N/A
250, SV-250

GEM1256

Does not fit

KBT25030, KGEMBIOD, KGEMDIV

Does not fit

KBT25030, KGEM200

KBT25030, KGEM250

N/A

N/A

Ice Machine Specifications

	Model	WxDxH	Basic			Minimum Circuit	Maximum	Refrigerant
	Number	(Inches)	Electrical		Condenser	Ampacity	Fuse Size	Charge oz. R404

GEM0650R		21x24x27	115/60/1		Remote	22.5	30	208
GEM0956R		21x24x27 208-230/60/1 Remote				14.1	20	208
GEM1256R		30x24x27	208-230/60/1		Remote	17.3	25	208

Page 4

Image 10

Ice-O-Matic GEM0956R, GEM1256R, GEM0650R installation manual Bin Application, Ice Machine Specifications

Contents

Pearl Ice Series By Ice-O-MaticPage Introduction Keep this manual for future reference Table Of Contents Visible Loss or Damage Freight Claim ProcedureInspect Promptly Concealed Loss or Damage Warranty Governing LAW For the Installer GEM0650/0956R GEM1256R Ice Machine Specifications Bin Application Ice machine LocationStorage Bin Water Limitations Pearl Ice Number ERC Dimensions Inches GRC1001 GRC1061 GCR2061Remote Condenser Line Sets Calculation Formula Remote Condenser LocationCalculation Example Roof Attachment Remote Condenser LocationPrecharged Line Set Routing Typical Installation Coupling Instructions Initial Connections Final Connections Water Inlet For the PlumberDrains Ice Machine For the Electrician Completed Installation Final Check List Pre-Start Inspection There are no adjustments to make, so replace the panelsStart Up Start Up Component Description Control Board GEM0650/0956/1256 Remote Electrical Sequence Water Level Operation WaterWater Water System Refrigeration Schematic Operation Refrigeration Low Condensing Temperature Pump Down Operation Performance Sanitizing and Cleaning Condenser Maintenance Brush in direction of fins Bearing Maintenance Bearing Maintenance Bin Control Sensor Sensor MaintenanceWater Sensor Auger Maintenance Auger Service Diagnosis Symptom Possible Cause Probable Correction Symptom Control System Diagnostics High pressure cut out check Water Reservoir Water Reservoir, Bin ControlBin Controls Ice Level Sensors To Remove the Breaker Bearing Assembly Bearing and Breaker Auger To Remove the Auger Removal of the Water Seal To Replace the Water Seal Water SealTo Remove the Water Seal Replacing the Water Seal To Replace the Evaporator EvaporatorTo Reassemble the Evaporator and Auger To Check the Gear Motor To Remove and Repair the Gear Motor AssemblyGear Motor To Inspect the Gear Motor To Remove the Condenser Fan Motor Assembly Fan Blade and Motor Refrigeration Service Charging Procedure GEM0650R Wiring Diagram Wiring Diagram GEM0650R GEM0956R Wiring Diagram Wiring Diagram GEM0956R GEM1256R Wiring Diagram Wiring Diagram GEM1256R Service History What to Do Before Calling for Service