Icom IC-F3062S, IC-F3061T, IC-F3062T, IC-F3061S, IC-F3063S Adjustment Procedures, Preparation

JIG CABLE.

ADJUSTMENT SOFTWARE

SECTION 6 ADJUSTMENT PROCEDURES

6-1 PREPARATION

When adjusting IC-F3060 series, the optional CS-F3060 ADJ(Rev. 1.1 or later), OPC-966 JIG CABLE (modifi ed OPC-966 CLONING CABLE; see illustration page 5-2) and below test equipments are required.

▄REQUIRED TEST EQUIPMENT

EQUIPMENT	GRADE AND RANGE		EQUIPMENT	GRADE AND RANGE
FM deviation meter	Frequency range	: DC–300 MHz	Attenuator	Power attenuation	: 20 or 30 dB
	Measuring range	: 0 to ±10 kHz		Capacity	: 10 W
	Frequency range	: 0.1–300 MHz	Standard signal	Frequency range	: 0.1–300 MHz
Frequency counter	Frequency accuracy	: ±1 ppm or better			: 0.1 µV to 32 mV
			generator (SSG)	Output level
	Sensitivity	: 100 mV or better			(–127 to –17 dBm)
	Measuring range	: 1–10 W	Oscilloscope	Frequency rang	: DC–20 MHz
	Frequency range	: 100–300 MHz		Measuring range	: 0.01–20 V
RF power meter
	Impedance	: 50 Ω	External speaker	Input impedance	: 8 Ω
	SWR	: Better than 1.2 : 1
				Capacity	: 1 W or more

▄SYSTEM REQUIREMENTS

•Microsoft® Windows® 98/98SE/Me/2000/XP

•RS-232C serial port (D-sub 9 pin)

▄ADJUSTMENYT SOFTWARE INSTALLATION q Quit all applications when Windows is running.

w Insert the CD into the appropriate CD drive.

e Double-click the “Setup.exe” contained in the ‘CS-F3060 ADJ’ folder in the CD drive.

r The “Welcome to the InstallShield Wizard for CS-F3060 ADJ” will appear. Click [Next>].

t The “Choose Destination Location” will appear. Then click [Next>] to install the software to the destination folder. (e.g. C:\Program Files\Icom\CS-F3060 ADJ)

y After the installation is completed, the “InstallShield Wiz- ard Complete” will appear. Then click [Finish].

u Eject the CD.

i Program group ‘CS-F3060 ADJ’ appears in the ‘Programs’ folder of the start menu, and ‘CS-F3060 ADJ’ icon ap- pears on the desk top screen.

▄BEFORE STARTING SOFTWARE ADJUSTMENT

Clone the adjustment frequencies into the transceiver, and set the confi guration using with the CS-F3060 CLONING SOFT- WARE before starting the software adjustment. Otherwise, the software adjustment can not be started.

CAUTION!: BACK UP the originally programmed mem- ory data in the transceiver before program- ming the adjustment frequencies.

When program the adjustment frequencies into the transceiver, the transceiver’s memory data will be overwritten and lose original memory data at the same time.

Microsoft and Windows are registered trademarks of Micro- soft Corporation in the U.S.A. and other countries.

▄STARTING SOFTWARE ADJUSTMENT

q Connect the transceiver and PC with OPC-966 w Turn the transceiver power ON.

e Boot up Windows, and click the program group ‘CS-F3060 ADJ’ in the ‘Programs’ folder of the [Start] menu, then CS-F3060 series ADJ’s window appears.

r Click ‘Connect’ on the CS-F3060 ADJ’s window, then appears transceiver’s up-to-date condition.

t Set or modify adjustment data as specifi ed.

• ADJUSTMENT FREQUENCY LIST

CH	FREQUENCY	ADJUSTMENT ITEM
1	174.000 MHz	TX power	: Low1
		Mode	: Narrow
2	154.900 MHz	TX power	: Low1
		Mode	: Narrow
3	155.000 MHz	TX power	: High
		Mode	: Wide
4	155.000 MHz	TX power	: Low2
		Mode	: Wide
5	155.000 MHz	TX power	: Low1
		Mode	: Wide
6	136.000 MHz	TX power	: Low1
		Mode	: Wide
7	174.000 MHz	TX power	: Low1
		Mode	: Wide
8	136.000 MHz	TX power	: Low1
		Mode	: Narrow
9*	155.000 MHz	TX power	: Low1
		Mode	: Digital
10*	136.000 MHz	TX power	: Low1
		Mode	: Digital
11*	174.000 MHz	TX power	: Low1
		Mode	: Digital
		TX power	: Low1
12	155.000 MHz	Mode	: Wide
		CTCSS	: 151.4 Hz
13	155.000 MHz	TX power	: Low1
		Mode	: Narrow
14†	155.000 MHz	TX power	: Low1
		Mode	: Middle
15†	136.000 MHz	TX power	: Low1
		Mode	: Middle
16†	174.000 MHz	TX power	: Low1
		Mode	: Middle

*; Necessary only when the optional UT-119 is installed.

†; [EUR-01] only

6 - 1