Manuals / InFocus / Computer Equipment / Projector

InFocus LS700 warranty NOTE The Manual Sync Manual Tracking, Horiz. Posi

Models: LS700

1 55

Download 55 pages 20.46 Kb

Page 29

NOTE: The Manual Sync,

Image Position

This setting allows you to re-position a 16x9 or native mode video image. Select among top, bottom, and center by highlight- ing Image Position in the menus and clicking either mouse but- ton to cycle through the options.

Overscan

This option crops all the edges of the image to remove noise gen- erated on the edges by your source.

DVD Optimized

This option improves the image quality of DVD images. Only turn this feature on if you are using a DVD player. Do not turn it on if you are using a VCR. This feature is only available for NTSC video.

Manual Sync

The projector adjusts signal synchronization automatically for most computers. But if the projected computer image looks fuzzy or streaked, try turning Auto Image off then back on again. If the image still looks bad, try adjusting the signal synchronization manually as described below.

1Turn Auto Image off.

2Move down to Manual sync, then press either mouse button repeatedly until the image is sharp and free of streaks.

Manual Tracking

The tracking function adjusts the projector to match the signal from your computer. The projector usually adjusts the tracking automatically when you connect your computer. However, if the display shows evenly spaced, fuzzy, vertical lines or if the pro- jected image is too wide or too narrow for the screen, try turning Auto Image off then back on again. If the image is still bad, try adjusting the tracking manually as described below.

1Turn Auto Image off.

2Press either mouse button repeatedly until the fuzzy vertical bars are gone.

NOTE: The Manual Sync,

Manual Tracking, Horiz. Posi-

tion and Vert. Position buttons are available only for computer sources. The projector sets these options automatically for a video source.

25

Image 29

InFocus LS700 warranty NOTE The Manual Sync Manual Tracking, Horiz. Posi

Contents

Safety Instructions TABLE OF CONTENTSSetting up the Projector Using the ProjectorIndex Maintenance & TroubleshootingAppendix Warning Don’t block ventilation openings SAFETY INSTRUCTIONSWarning Hot surface. Do not touch INTRODUCTION Image ResolutionCompatibility Unpacking the Projectoron the configuration you’ve ordered NOTE The contents of your shipping box may vary dependingShipping box contents I n t r o d u c t i o nremote control receiver connector panel elevator buttonpower connectorIf You Need Assistance WarrantyUsage Guidelines SETTING UP THE PROJECTOR wired remote Preparing to Connect Your Equipment to the Projectoraccessory S e t t i n gaudio/video cable Connecting a Video Player6 Attach external speakers see the following page NOTE The external speakers must be amplified Connecting an External SpeakerConnecting external speakers Connecting a Computer Powering up the Projector and Adjusting the Image Turning Off the Projector Basic Image Adjustment USING THE PROJECTORLeveling knob Adjusting the ProjectorFocus ring, zoom ring, and elevator button To raise the projector 1 Press and hold the elevator button Figure Using the Remote and Keypad Buttons Using the Remote ControlPress computer to display your computer image Video VolumeStandby Keypad only buttons Brightness Remote only buttons PowerScribble LightDisk mouse and mouse buttons on keypad and remote Using the MenusOn-screen menus Adjusting the brightness changes the intensity of the image This setting adjusts the transition between color edges Audio Menu Auto Image Image MenuAuto Resize-Computer Auto Resize-VideoNOTE The Manual Sync Manual Tracking, Horiz. Posi Follow these steps to manually adjust the horizontal position Default Source Controls MenuVideo Standard Standby TimePlug and Play Auto Source SelectDisplay Messages Display Startup ScreenStatus menu Language menuLanguage menu Status menuHelp menu Cleaning the Fan Intake Filter MAINTENANCE & TROUBLESHOOTINGCleaning the Lens 4 Replace the filter 3 Clean the filterM a i n t e n a n c e T r o u b l e s h o o t i n gReplacing the Projection Lamp 7 Align the new lamp module in the correct direction Using the Kensington Lock Replacing the Batteries in the Remote ControlTroubleshooting Solutions to Common Problems Change the Color Temperature. See “Color Temperature” on page Problem Image is out of focus Problem Computer image isn’t centered on the screenProblem Image is too wide or narrow for screen Problem Image and menus are upside down Problem Image and menus are reversed left to rightProblem the projector displays vertical lines, “bleeding” or spots Problem The screen resolution is not rightProblem Remote not operating correctly Problem Lamp seems to be getting dimmerProblem Lamp shuts off Temperature APPENDIX SpecificationsDimensions WeightInput Power Requirements Remote ControlA p p e n d i Video Audio InputStandard Accessories AccessoriesPower Cords one ships with projector, type depends on country ship with the projectorA p p e n d i Optional AccessoriesProjected image size Projected Image SizeImage Size, Width and Height for Lens at Maximum A p p e n d iImage Size Distance toNumerics INDEXI n d e Page I n d e