Insignia NS-HT511 Listening to the radio, Dim, AUDIO, M.Opt, TUNER, TUNER, DIMMER, Dimmer, Normal, MUTING, TUNING, RECEIVER, RECEIVER, M.Optimizer, Using headphones

						Insignia NS-HT511 Home Theater System
					The SLEEP indicator lights on the display when
		Notes
					the sleep timer has been set. The specified sleep
			• When AM or FM radio is used, the band, preset
					time appears on the display for about five
			number, and frequency are displayed.
			• If the input signal is analog, no format		seconds, then the previous display reappears.
			information is displayed. If the input signal is
			PCM, the sampling frequency is displayed. If the		Tip
			input signal is digital but not PCM, the signal			• To cancel the sleep timer, press SLEEP
			format is displayed. Information is displayed for			repeatedly until the SLEEP indicator goes off.
			about three seconds, then the previously			• To check the time remaining until the receiver
			displayed information reappears.			turns off, press SLEEP. If you press SLEEP while
			• The input source is displayed with the default			the sleep time is being displayed, the sleep time
			name even when you have selected a name. See			is shortened by 10 minutes.
			“Setting up HDMI (HDMI Setup menu)” on page
				Using headphones
			24.
Using the music optimizer				To use headphones:
	The music optimizer enhances the sound quality of			• Connect a pair of stereo headphones with a
				standard plug (1/4 in. or 6.3 mm) to the PHONES
	compressed music files.
				jack.
	To use the music optimizer:
					Tip
1		Press AUDIO, then press or to select				• Always turn down the volume before
		M.Optimizer.				connecting your headphones.
2		Press or to select On.				• While the headphones plug is inserted in the
						PHONES jack, the speakers are turned off.
		The M.Opt indicator lights on the display.
						• When you connect a pair of headphones, the
						listening mode is set to Stereo, unless it is
		Notes				already set to Stereo, Mono, or Direct.
			• The music optimizer function only works with			• The listening modes cannot be selected while a
			PCM digital audio input signals with a sampling			pair of headphones is connected.
			rate below 48 kHz and analog audio input	Listening to your receiver
			the direct listening mode is selected.
			signals. The music optimizer is disabled when
			• The setting is stored individually for each input
			selector.
					Important

Setting the display brightness

You can adjust the brightness of the receiver’s display.

To set the display brightness:

•Press RECEIVER, then press DIMMER repeatedly to select: Dim, Dimmer, or Normal brightness.

Muting the receiver

To mute the receiver:

•Press RECEIVER, then press MUTING.

The output is muted and the MUTING indicator flashes on the display.

The procedures described in this section use the buttons on the front panel, unless otherwise specified.

Listening to the radio

With the built-in tuner you can enjoy AM and FM radio stations. You can store your favorite stations as presets for quick selection.

To listen to the radio:

•Press TUNER to select either AM or FM (each time you press TUNER, the radio band changes between AM and FM).

In this example, FM has been selected.

BandFrequency

Tip

•To unmute, press MUTING again or adjust the volume.

•Muting is also cancelled when the receiver is set to Standby.

Using the sleep timer

With the sleep timer, you can set the receiver to turn off automatically after a specified period.

To use the sleep timer:

•Press RECEIVER, then press SLEEP repeatedly to select the sleep time you want.

The sleep time can be set from 90 to 10 minutes, in 10 minute steps.

•To automatically tune to a station:

•Press TUNING MODE until the AUTO indicator appears on the display.

•Press TUNING or . The receiver automatically searches for stations and stops when a station is found.

FM Stereo

AUTO

TUNED

18 www.insigniaproducts.com