Insignia NS-HT511 Home Theater System

- - - - -–Select if you are using an analog audio input.

 

The Center Width setting lets you adjust the width

 

 

 

 

of the sound from the center speaker when using

 

Notes

 

 

the Dolby Pro Logic II Music listening mode.

 

 

• When an HDMI IN is assigned to an input

 

Normally, if you’re using a center speaker, the center

 

 

selector as explained here, the digital audio

 

 

 

 

channel sound is output by only the center speaker.

 

 

input for that input selector is automatically set

 

 

 

 

(If you’re not using a center speaker, the center

 

 

to the same HDMI IN. In addition to the usual

 

 

 

inputs, such as COAX, you can also select HDMI

 

channel sound is distributed to the front left and

 

 

inputs.

 

right speakers to create a phantom center). This

 

 

• The available sampling rate for PCM signals

 

setting controls the front left, right, and center mix,

 

 

from a digital input (optical and coaxial) is

 

allowing you to adjust the weight of the center

 

 

32/44.1/48/88.2/96 kHz/16, 20, 24 bit.

 

channel sound.

Adjusting the audio (Audio Adjust menu)

 

Submenu

Configuration

With the audio adjust settings you can adjust the

 

Panorama

On– Turns the Panorama function on.

sound and listening modes to your taste.

 

Off–Turns the Panorama function off.

 

 

Setting the Multiplex (Input Ch(Mux) submenu) and

 

Dimension

–3 to 0 to +3

Mono (Input Ch(Mono) submenu)

 

 

 

 

Center Width

0 to 3 to 7

The multiplex setting determines which channel of

 

 

 

 

 

 

 

a stereo multiplex source is output. Use it to select

 

 

 

audio channels or languages with multiplex

Setting the DTS options (Center Image submenu)

sources, multilingual TV broadcasts, and so on.

 

 

 

The mono setting specifies the channel to be used

The DTS Neo:6 Music listening mode lets you create

6-channel surround sound from 2-channel stereo

for playing any 2-channel digital source, such as

sources. With this setting, you can specify by how

Dolby Digital, or 2- channel analog/PCM source in

much the front left and right channel output is

the Mono listening mode.

attenuated in order to create the center channel.

 

OptionSettings

Main (default)–The main channel is output.

MultiplexSub–The sub channel is output.

M/S–Both the main and sub channels are output.

L+R–Both the left and right channels are output.

MonoLeft–Only the left channel is output. Right–Only the right channel is output.

A value 0 is only audible from the center speaker. A value of more than 0 is audible from the left and right speakers as well.

Submenu

Configuration

Center Image

0 to 2 (default) to 5

 

 

Setting the Dolby options (Panorama, Dimension, and Center Width submenus)

These settings only apply to 2-channel stereo sources.

The Panorama setting lets you broaden the width of the front stereo image when using the Dolby Pro Logic II Music listening mode.

The Dimension setting lets you move the sound field forward or backward when using the Dolby Pro Logic II Music listening mode. Higher settings move the sound field backward. Lower settings move it forward. If the stereo image feels too wide, or there’s too much surround sound, move the sound field forward to improve the balance. Conversely, if the stereo image feels like it’s in mono, or there’s not enough surround sound, move it backward.

Adjusting the Theater-Dimensional setting (Listening Angle submenu)

This setting lets you optimize the Theater-Dimensional listening mode by specifying the angle of the front left and right speakers relative to the listening position. Ideally, the front left and right speakers should be equidistant from the listening position and at an angle close to one of the two available settings.

20°/40°

SubmenuOptions

Listening Angle

Wide (default)–The listening angle is 40 degrees. Narrow–The listening angle is 20 degrees.

www.insigniaproducts.com

23