Integra DTR-8.2 Rear panel facilities, Digital INPUT/OUTPUT coaxial and optical, Coaxial cable

Rear panel facilities

Here is an explanation of the terminals found on the rear of the DTR-

8.2and how they are used. Before connecting your audio and video components, be sure to read this section carefully and then proceed to the explanations on how to connect each individual component (see page 18).

•Be sure to always refer to the instructions that came with the component that you are connecting.

•Do not plug in the power cord until all connections have been made.

•For input jacks, red connectors (marked R) are used for the right channel, white connectors (marked L) are used for the left channel, and yellow connectors (marked V) are used for video connection.

•Insert all plugs and connectors securely. Improper connections can result in noise, poor performance, or damage to the equipment.

Improper connection

Inserted completely

•Do not bind audio/video connection cables with power cords and speaker cables. Doing so may adversely affect the picture and sound quality.

DIGITAL	PRE OUT
OUTPUT	R	L	ANTENNA
OPT	FRONT
1
	SUB		CENTER
2			AM

	AUDIO	VIDEO	S VIDEO
			MONITOR
			OUT
R	L
	OUT		ZONE 2

COMPONENT
VIDEO	FRONT SPEAKERS		SURR SPEAKERS
OUTPUT	R	L	R	L	AV RECEIVER
Y					MODEL NO. DTR-8.2
I R OUT 40K
A	B
PB

COAX	SURR
1
	SURR
	BACK/
2	ZONE 2		FM
			75
3	FRONT	MULTI CH
		INPUT
			AUDIO
OPT	SUB	R	L
		CENTER
1			PH
	SURR
2			CD
	SURR		OUT
	BACK
3
			TAPE
4
	GND	R	IN
DIGITAL			L
			AUDIO
INPUT

	IN		DVD
	OUT
			VIDEO 1
	IN
	OUT
			VIDEO 2
	IN
	IN		VIDEO 3
	IN		VIDEO 4
R	L	VIDEO	S VIDEO
	AUDIO

PR	I R OUT 56K
INPUT 1
Y	ZONE A		CAUTION:
	OUT
			SPEAKER
	ZONE B		IMPEDANCE
PB			4 OHMS MIN. OR
	OUT
			6 OHMS MIN.
			/SPEAKER
	ZONE C		SEE
PR			INSTRUCTION
	OUT		MANUAL FOR
INPUT 2		CENTER	CORRECT	R
	ZONE D		SETTINGS.
Y		SPEAKER	I R
	OUT			A	ZONE 2
			IN
					12V
PB		RS 232			TRIGGER
	DC IN
	24V 4A		OUT		B
PR
					REMOTE
					CONTROL

AC OUTLETS

SURR
BACK
/ ZONE 2	SWITCHED
SPEAKERS	TOTAL 120W 1A MAX.

L

AC INLET

DIGITAL INPUT/OUTPUT (coaxial and optical)

These are the digital audio inputs and outputs on the rear panel. There are three digital inputs with coaxial jacks and four with optical jacks. The inputs accept digital audio signals from a compact disc, LD, DVD, or other digital source component. For digital output, there is 1 optical output. The digital outputs can be connected to MD recorders, CD recorders, DAT decks, or other similar components.

•Since an analog connection must be made when using REC OUT or ZONE 2, make sure that the connection to the input source is not digital only, but analog as well.

•When using one of the optical input or output jacks, remove the protective cap and keep it safely. When the jack is not used, replace the protective cap.

•When using an optical input or output jack, always use an optical fiber cable.

COAXIAL	Coaxial cable
OPTICAL	Optical fiber cable

Optical digital input terminal

An optical digital input terminal is equipped with a protection cap. When connecting, remove this cap. When not using, put the cap back on the terminal.

14