Integra DTR-8.2 12V Trigger A/B/ZONE 2 terminal, Power on/ready function, Direct change function

Rear panel facilities

AC OUTLETS

The DTR-8.2 is supplied with AC mains outlets for connecting the power cords from other devices so that their power is supplied through the DTR-8.2. By doing this, you can use the Standby/On button on the DTR-8.2 to turn on and off the connected devices as well.

Caution:

Make sure that the total capacity of the other components connected to this unit does not exceed the capacity that is printed on the rear panel (e.g., 120 watts).

AC OUTLETS

AC 120V 60 Hz

SWITCHED

TOTAL 120W 1A MAX.

AC INLET

Plug the supplied power cord into this AC INLET and then into the power outlet on the wall.

•Do not use a power cord other than the one supplied with the DTR-8.2. The power cord supplied is designed for use with the DTR-8.2 and should not be used with any other device.

•Never have the power cord disconnected from the DTR-8.2 while the other end is plugged into the wall outlet. Doing so may cause an electric shock. Always connect by plugging into the wall outlet last and disconnect by unplugging from the wall outlet first.

AC INLET

Power cord (supplied)

To an AC wall outlet

12V TRIGGER A/B/ZONE 2 terminal

These terminals are provided so that you can use the operation of the DTR-8.2 control the operation of another externally connected device. Connect the component to this 1/8-inch mini-jack terminal and when the set input source is selected, the device will turn on. Set the 12V TRIGGER terminal using the Setup menu: Input setup → 12V trigger (see page 42).

When the DTR-8.2 is in the ZONE 2 mode, this terminal outputs at 12 V/100 mA.

(RI)

The terminal on the DTR-8.2 is for connecting other Integra/

Onkyo components equipped with the same terminal. When a

component is -connected, you can point the remote controller supplied with the DTR-8.2 at the sensor on the DTR-8.2 and operate that component without having to switch remote controllers.

In addition, by connecting components to the terminal, you can also perform the system operations given below.

Power on/ready function

When the DTR-8.2 is in the standby state, if an -connected component is turned on, then the DTR-8.2 also turns on and the input source selected at the DTR-8.2 automatically switches to that component.

If the power cord for an -connected component is connected to the AC OUTLET on the DTR-8.2, or if the DTR-8.2 is turned on, this function will not work.

Direct change function

When the play button is pressed at an -connected component, the input source selected at the DTR-8.2 automatically changes to that component.

Power off function

When the DTR-8.2 is placed in the standby state, all -connected components are also automatically put into the standby state.

CAUTION

If an MD recorder is connected to the TAPE jack on the DTR-8.2, switch the Input Selector from TAPE to MD (see page 28).

DTR-8.2

connector

Ex: Integra/Onkyo CD player

connector

Ex: Integra/Onkyo cassette tape deck

To connect components using the terminal, simply connect a

remote control cable from this terminal to the terminal of the

other component. An remote control cable with a 1/8-inch (3.5-

mm)miniature two-conductor plug comes with every cassette tape deck, compact disc player, MD recorder, and DVD player that has an terminal.

•When performing operations with -connected components

using the system, do not use the remote zone (Zone 2).

•For remote control operation, the audio connection cables must also be connected.

•If a component has two terminals, you can use either one to connect to the DTR-8.2. The other one can be used to daisy chain with another component.

16