ADE-9040 User’s Manual

2.3.22 DVI Connector (CN31)

 

Description

 

PIN No.

 

 

PIN No.

 

Description

 

 

 

 

 

 

 

HPDET

 

1

 

2

 

Ground

 

 

 

 

 

 

 

Ground

3

4

 

DVIDATA

 

 

 

 

 

 

 

TDC0#

 

5

 

6

 

DVICLK

 

 

 

 

 

 

 

TDC0

7

8

 

Ground

 

 

 

 

 

 

 

Ground

 

9

 

10

 

TLC#

 

 

 

 

 

 

 

TDC1#

11

12

 

TLC

 

 

 

 

 

 

 

TDC1

 

13

 

14

 

Ground

 

 

 

 

 

 

 

Ground

15

16

 

Ground

 

 

 

 

 

 

 

TDC2#

 

17

 

18

 

Ground

 

 

 

 

 

 

 

TDC2

19

20

 

+5V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Signal

 

 

Type

 

 

 

 

 

 

Description

 

 

 

 

 

TDC0,TDC0#

 

 

O

 

 

 

DVI Data Channel 0 Output: These

pins

provide

the

DVI

differential

 

 

 

 

 

 

output for data channel 0 (Blue).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TDC1,TDC1#

 

 

O

 

 

 

DVI Data Channel 1 Output: These

pins

provide

the

DVI

differential

 

 

 

 

 

 

output for data channel 1 (Green).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TDC2,TDC2#

 

 

O

 

 

 

DVI Data Channel 2 Output: These

pins

provide

the

DVI

differential

 

 

 

 

 

 

output for data channel 2 (Red).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Hot Plug Detect (internal pull-down): This input determines whether the

 

 

 

 

 

 

 

 

 

HPDET

 

 

I

 

 

 

DVI is connected to a DVI monitor. When terminated\, the monitor is

 

 

 

 

 

 

required to apply a voltage greater than 2.4 volts. Changes on the status of

 

 

 

 

 

 

 

 

this pin will be relayed to the graphics controller via the P-OUT/TLDET* or

 

 

 

 

 

 

 

 

GPIO(1)/TLDET* pin pulling low.

 

 

 

 

 

 

DVIDATA

 

 

I/O

 

 

 

DVI I2C Data: This signal is used as the I2C DOC clock for a digital display

 

 

 

 

 

 

connector

(i.e. TV-Out Encoder, TMDS transmitter ). This

signal is

 

 

 

 

 

 

 

 

tri-stated during a hard reset.

 

 

 

 

 

 

DVICLK

 

 

I/O

 

 

 

DVI DOC Clock: This signal is used as the DOC clock for a digital display

 

 

 

 

 

 

connector (i.e. primary digital monitor). This signal is tri-stated during a

 

 

 

 

 

 

 

 

hard reset.

 

 

 

 

 

 

 

 

TLC,TLC#

 

 

O

 

 

 

DVI Clock Output: These pins provide the differential clock outputs to the

 

 

 

 

 

 

DVI interface corresponding a data on TDC(0:2) outputs.

 

 

 

 

 

 

 

 

 

 

 

 

2.3.23 Serial ATA 1/2/3/4 Connectors (SATA1, SATA2, SATA3, SATA4)

These SATA connectors support Serial ATA 300. Each SATA connector can only support one serial ATA device. Note: With most storage devices, there is a power cable

that you need attach to a power source (power supply).

20 / 55