Manuals / Brands / Computer Equipment / Computer Hardware / Intel / Computer Equipment / Computer Hardware

Intel ADE-9040 ADE-9040User’s Manual, 4.1.2.9.5.1Emulation Type, 4.1.2.9.5USB Mass Storage Device Configuration

1 55

Download 55 pages, 746.4 Kb

ADE-9040 User’s Manual

4.1.2.9.5USB Mass Storage Device Configuration4.1.2.9.5.1Emulation Type

If Auto, USB devices less than 530MB will be emulated as Floppy and remaining as hard drive. Forced FDD option can be used to force a HDD formatted drive to boot as FDD (Ex. ZIP drive)

42 / 55

Contents

Intel® Core™ 2 Duo Desktop Q965 ATX Mother Board ADE-9040User’s Manual Copyright Trademark Technical Support How to Use This Manual Chapter 1: Introduction Chapter 2: Hardware Configuration Setting Chapter 3: System Installation Chapter 4: BIOS Setup Information Specifications Dimensions Board Layout Jumpers & Connectors Installing the ATX Mother Board Revision History Page 1.Introduction 1.2Packing Check List 1.3Specifications Page 1.4System Architecture Page Page 2.Hardware Configuration Setting 2.2Jumpers & Connectors JUMPERS FUNCTION REMARK JP1 2.3Jumpers/Connectors Setting 2.3.1RTC Clear CMOS (JP1) 2.3.2 BIOS Write Protect (JP2) 2.3.3 AT/ATX Power Select (JP3) 2.3.4 DVI Select (JP4) 2.3.12 Audio Connector (CN15) (CN17) 2.3.16 VGA & Serial Port 1 Connector (CN20) 2.3.17 Serial Port 4 Connector (CN21) 2.3.18 Serial Port 3 & 2 Connectors (CN29 2.3.19 4-pinATX Power Connector (CN25) 2.3.21 Front Panel Connector (CN27) 2.3.20 24-pinATX Power Connector (CN26) 2.3.22 DVI Connector (CN31) 2.3.23 Serial ATA 1/2/3/4 Connectors (SATA1, SATA2, SATA3, SATA4) Page 3.System Installation 3.1.2 Installing Intel µFC-LGA775 CPU Fan, and Heat Sink 3.1.3 Removing CPU Warning Instructions 3.2Main Memory NOTE: 3.3Installing the ATX Mother Board WARNING: 3.4.1 Dual Marvell Gigabit Ethernet Controllers Yellow LED indicates transmit and receive activity Green LED indicates Link speed Page 4.BIOS Setup Page 4.1.2.1 CPU Configuration 4.1.2.1.1Max CPUID Value Limit 4.1.2.1.2Execute Disable Bit 4.1.2.1.3Intel ® SpeedStep (tm) tech 4.1.2.1.4Intel C-Statetech 4.1.2.2 IDE Configuration SATA#1 Configuration Configure SATA#1 as 4.1.2.2.3Primary/Secondary IDE Master/Slave 4.1.2.2.4Hard Disk Write Protect 4.1.2.2.6ATA(PI) 80Pin Cable Detection Page 4.1.2.3.1Serial Port1/2 Address 4.1.2.3.2Serial Port2 Mode 4.1.2.3.3Restore on AC Power Loss by IO 4.1.2.3.4Serial Port3/4 Address 4.1.2.3.5Serial Port3/4 IRQ 4.1.2.4 Hardware Health Configuration 4.1.2.4.1H/W Health Function 4.1.2.4.2FAN 1 Mode Setting 4.1.2.4.3Temperature 1 Limit of Start 4.1.2.4.4Fan 1 Start PWM 4.1.2.4.8Fan 2 Start PWM 4.1.2.4.9Slope PWM 4.1.2.5 ACPI Configuration 4.1.2.5.1ACPI Aware O/S 4.1.2.6 APM Configuration 4.1.2.6.1Power Management/APM 4.1.2.6.2Video Power Down Mode 4.1.2.6.3Hard Disk Power Down Mode 4.1.2.6.4Suspend Time Out 4.1.2.6.7Power Button Mode 4.1.2.6.8Resume On Ring 4.1.2.6.9Resume On LAN Resume On PME# Resume On RTC Alarm Page 4.1.2.8 Remote Access Configuration 4.1.2.8.1Remote Access 4.1.2.8.2Serial Port Number 4.1.2.8.3Flow Control 4.1.2.8.4Redirection after BIOS POS 4.1.2.9 USB Configuration 4.1.2.9.1Legacy USB Support 4.1.2.9.2Port 64/60 Emulation 4.1.2.9.3USB 2.0 Controller Mode 4.1.2.9.4BIOS EHCI Hand-Off 4.1.2.9.5USB Mass Storage Device Configuration 4.1.2.9.5.1Emulation Type Page 4.1.3.1 Clear NVRAM 4.1.3.2 Plug & Play O/S 4.1.3.3 PCI Latency Timer 4.1.3.4 Allocate IRQ to PCI VGA 4.1.3.5 Palette Snooping DMA Channel 0/1/3/5/6/7 4.1.3.10 Reserved Memory Size Page 4.1.4.1 Boot Settings Configuration 4.1.4.1.1Quick Boot 4.1.4.1.2Quiet Boot 4.1.4.1.3AddOn ROM Display Mode 4.1.4.1.4Bootup Num-Lock 4.1.4.1.5Wait For ‘F1’ If Error 4.1.4.1.6Hit ‘DEL’ Message Display 4.1.4.1.7Interrupt 19 Capture 4.1.5Security Settings 4.1.5.1 Change Supervisor Password 4.1.5.2 Change User Password 4.1.5.3 Clear User Password Boot Sector Virus Protection Page 4.1.6.1 North Bridge Configuration 4.1.6.1.1Memory Remap Feature 4.1.6.1.2DRAM Frequency 4.1.6.1.3Configure DRAM Timing by SPD 4.1.6.1.4Initate Graphic Adapter 4.1.6.1.6PEG Port 4.1.6.2 South Bridge Configuration 4.1.6.2.1USB Functions 4.1.6.2.2USB 2.0 Controller 4.1.6.2.3HDA Controller 4.1.6.2.4Onboard Giga LAN 1/2 4.1.6.2.5SLP_S4# Min. Assertion Width 4.1.7Exit Options 4.1.7.1 Save Changes and Exit 4.1.7.2 Discard Changes and Exit 4.1.7.3 Discard Changes 4.1.7.4 Load Optimal Defaults