Intel ISP2150 Power Supply

42 ISP2150 2U Rack Server Platform Product Guide

Power Supply

Removing and Re-installing a Power Supply

To replace the power supply:

1. Unplug the power cord from the power source and from the power cord receptacle (A) at the

right rear side of the system.

2. Remove the top cover of the system. Refer to “Opening the Cover” on page 29.

3. Remove and save the two screws (B) from the power supply cover (C).

4. Grasp the bottom edge of the power supply cover and lift it up and away from the power

supply.

5. Grasp the sides of the power supply and slide it forward, out of the chassis.

OM09324

Figure 18. Replacing the Power Supply

A. Power cord receptacle

B. Screws

C. Cover

6. Slide the new power supply into the chassis and make sure it is seated in the chassis connector.

7. Close the power supply cover and re-insert the screws you set aside earlier.

8. Re-connect the power cord to the power cord receptacle and plug the cord back into its power

source.

Contents

Main Page Contents 1 Description 2 Upgrading and Installing Server Components 3 Configuration Software and Utilities 4 Solving Problems 5 Technical Reference 6 Product Regulation and Certification Information 7 Equipment Log and Power Consumption Worksheets Index Figures Tables Page 1 Description Server Board Features Table 1. Server Board Features Front Panel Controls and Indicators Back Panel Connectors Figure 3. Back Panel Connectors Table 2. NIC LEDs Major System Elements Figure 4. Major System Elements Server Board Connector and Component Locations Processor Memory 440GX Host Bridge / Memory Controller Peripherals Super I/O Chip Serial Ports Parallel Port Add-in Board Slots Video SCSI Controller IDE Controller Network Controller Keyboard and Mouse ACPI Server Management Baseboard Management Controller (BMC) Emergency Management Port Console Platform Event Paging Software Security Using Passwords Secure Mode Summary of Software Security Features Table 3. Software Security Features Checking the Power Cords Equipment Rack Precautions SAFETY WARNINGS 2 Upgrading and Installing Server Components Tools and Supplies Needed Warnings and Cautions SAFETY WARNINGS Page Bezel Opening and Closing the Front Bezel Locking and Unlocking the Front Bezel Attaching and Removing the Front Bezel Covers Processors Installing a Processor CAUTION, SINGLE-PROCESSOR CONFIGURATIONS Removing a Processor Memory Installing DIMMs Removing DIMMs Peripheral Devices Removing the Diskette Drive Re-installing the Diskette Drive Installing a Hard Drive Page Installing a Slim-line CDROM Drive Removing a CDROM Drive Add-in Cards Installing Add-in Cards Page Power Supply Removing and Re-installing a Power Supply System Mounts Installing the Front Bracket and Racking the System Installing the Front Bracket in a Cabinet Installing the Front Bracket in a Center-Mount, Relay Rack Installing the Rail Rack and Racking the System (Optional Accessory) Page Page Page Replacing the Back up Battery Page 3 Configuration Software and Utilities Table 4. Configuration Utilities Hot Keys Use the keyboards numeric pad to enter numbers and symbols. Table 5. Hot Keys Power On Self Test (POST) Using BIOS Setup Record Your Setup Settings If You Cannot Access Setup Starting Setup Setup Menus Main Menu Primary/Secondary IDE Master and Slave Submenu Keyboard Submenu Processor Settings Submenu Advanced Menu PCI Configuration Submenu PCI Device, Slot 1 - Slot 6 Submenus Integrated Peripheral Configuration Submenu Integrated Peripheral Configuration Submenu (continued) Advanced Chipset Control Security Menu Server Menu You can make the following selections on the Server Menu itself. System Management Submenu System Management Submenu (continued) Server Management Information Submenu Console Redirection Submenu PEP Management Submenu PEP Filter Submenu This submenu allows you to set which events or error conditions cause the system to page you. Boot Menu You can make the following selections on the Boot Menu itself. Boot Menu (continued) Boot Device Priority Hard Drive Removable Devices Exit Menu Using the System Setup Utility When to Run the System Setup Utility What You Need to Do Running the SSU Starting the SSU Page Customizing the SSU Launching a Task Resource Configuration Add-in (RCA) Window Defining an ISA Card Adding and Removing ISA Cards Modifying Resources System Resource Usage Multiboot Options Add-in Security Add-in To Set the User Password To Change or Clear the User Password To Set the Administrator Password To Change or Clear the Administrator Password SEL Manager Add-in FRU Manager Add-in SDR Manager Add-in Exiting the SSU Platform Event Paging Using Platform Event Paging Emergency Management Port Console How EMP Console Works Page Requirements Setting up the Server for the EMP System Management Submenu Console Redirection Submenu Main EMP Console Window Toolbar Status Bar EMP Console Main Menu Server Control Operations Connect Power On/Off Reset Phonebook Management Plug-ins SEL Viewer SDR Viewer FRU Viewer FRUSDR Load Utility When to Run the FRUSDR Load Utility What You Need to Do How You Use the FRUSDR Load Utility Command Line Format Parsing the Command Line Displaying Usage Information Displaying a Given Area Using Specified CFG File Upgrading the BIOS Preparing for the Upgrade Recording the Current BIOS Settings Obtaining the Upgrade Utility Creating a Bootable Floppy Diskette Creating the BIOS Upgrade Floppy Diskette Upgrading the BIOS Recovering the BIOS Changing the BIOS Language Using the Firmware Update Utility Running the Firmware Update Utility Installing Video Drivers Using the Adaptec SCSI Utility Running the SCSI Utility Page 4 Solving Problems Resetting the System Fault Resilient Booting Initial System Startup Running New Application Software After the System Has Been Running Correctly More Problem Solving Procedures Preparing the System for Diagnostic Testing Monitoring POST Verifying Proper Operation of Key System Lights Confirming Loading of the Operating System Specific Problems and Corrective Actions Power Light Does Not Light No Characters Appear on Screen Characters Are Distorted or Incorrect System Cooling Fans Do Not Rotate Properly Diskette Drive Activity Light Does Not Light Hard Disk Drive Activity Light Does Not Light CD-ROM Drive Activity Light Does Not Light Cannot Connect to a Server Problems with Network PCI Installation Tips Problems with Application Software Bootable CD-ROM Is Not Detected Error and Informational Messages Port-80 Codes and Countdown Codes Page Connectors ATX Style Front Panel Connector J6J1 A B C D E F Figure 43. ATX Style Front Panel Connector Table 8. ATX Style Front Panel Connector Pinout Main Power Connector Fan Interface Server Board Jumpers Figure 44. Jumper Locations Table 11. Server Board Jumper Summary General Procedure to Change Jumper Setting CMOS Jumper Password Jumper Recovery Boot Jumper Boot Block Write Protect Jumper FRB Timer Enable Jumper Chassis Intrusion Detection Jumper Page 6 Product Regulation and Certification Information Regulatory Information Safety Compliance For Information Technology Equipment EMC Compliance Regulatory Compliance Markings Electromagnetic Compatibility Notices FCC Declaration of Conformity (USA) ICES-003 (Canada) VCCI (Japan) BSMI (Taiwan) Lithium Battery Replacement Equipment Rack Precautions WARNINGS Cautions Use Only for Intended Applications Power Cords Page WARNING: English (US) WARNING: English (US) (continued) AVERTISSEMENT: Franais AVERTISSEMENT: Franais (suite) WARNUNG: Deutsch WARNUNG: Deutsch (Fortsetzung) AVVERTENZA: Italiano AVVERTENZA: Italiano (continua) ADVERTENCIAS: Espaol ADVERTENCIAS: Espaol (contina) 7 Equipment Log and Power Consumption Worksheets Equipment Log Page Page Worksheet, Calculating DC Power Usage Table 12. Power Usage Worksheet 1 Worksheet, Total Combined Power Used by the System Table 13. Power Usage Worksheet 2 Page Index A B C D E F H-I J-L N-P R S Page T-U V-W