Manuals / Intermec / Computer Equipment / Barcode Reader

Intermec F4 manual Introduction, Description, Chapter

Models: F4

1 83

Download 83 pages 42.04 Kb

Page 7

Chapter 1

Introduction

Description

The EasyCoder F4 is a sturdy medium-duty direct thermal/thermal transfer printer with a printhead resolution of 8 dots per mm (203.2 dots per inch) and a maximum print width of 104 mm (4.095 inches).

The EasyCoder F4 is delivered with the Intermec Programming Language (IPL-3) installed. There is also a version of the EasyCoder F4 that uses the Intermec Fingerprint Programming Language. Mechanically, the IPL version is identical to the Intermec Fingerprint version, but a few options are not supported by IPL-3, for example:

•Optional double serial and industrial interface boards

•Electronic keys

•Memory cards (except for ﬁrmware upgrading)

•EasySet Bar Code Wand

•Real Time Clock Circuit

In most respects, the EasyCoder F4 IPL version is compatible with other IPL printers from Intermec. Please refer to Appendix 4 for a list of supported IPL-3 commands.

6	Intermec EasyCoder F4 – Installation & Operation IPL Version, Ed. 3

Image 7

Intermec F4 manual Introduction, Description, Chapter

Contents

EasyCoder F4 Bar Code Label Printer Contents Contents, Appendix GS Notice Germany FCC Notice United States of AmericaDOC Notice Canada Canadian Dept. of Communication Ministère des Communications du CanadaEasyCoder F4 Declaration of Conformity89/336/EEC and 73/23/EEC Description IntroductionChapter Voltage range. It also contains various signs of approval Safety PrecautionsUnpacking InstallationFront View Rear View Media Compartment Media Compart- ment, Media Supply Positions Omitted in dedicated direct thermal printing models Print MechanismConnections Power ComputerControl Lamps Display Controls and IndicatorsBeeper KeyboardStarting Up Switching OnTear-Off Media LoadTear-Off, Media is guided with a minimum of play Pull downwards Tear-Off with Quick-Load Tear-Off with Quick-Load, Self-strip Peel-OffPeel-Off, Insert the start of the liner under the lip Peel-Off, Quality or cause unnecessary wear to the printhead External SupplyStraight-through printing-preferably with Quick-Load There is no need to remove the media supply roll postRibbon Load Thermal Transfer PrintingRibbon Load, Setting Up the Printer Ribbon Load, Communication Setting Up the PrinterDescription Default Setup Test/ServiceParity Serial CommunicationBaud Rate Data BitsPrinting Setup Parameters,Serial Communication, Protocol Printhead hot Label at strip pin Label skippingReady Serial Communication, Protocol,Testprint Test/ServiceTest/Service, Label Length MediaMedia Type Paper TypeMedia, Darkest. Default value is 0%Darkness Entering Setup Mode At Installation Setup ModeNavigating in Setup Mode Setup Mode Overview, Part From previous Press Setup to exit the Setup Mode Introduction OptionsIntegral Liner Takeup Unit DTP ModelInch Adapter Quick-Load Guides Label Taken Sensor Interface Boards Symptom Possible Cause Remedy Refer to TroubleshootingPrinthead Cleaning MaintenanceRemove any media and transfer ribbon Printhead Cleaning,Printhead Cleaning, External Cleaning Cleaning the Media Guides Printhead Replacement Printhead Replacement, Printhead Replacement, Narrow Media Adjustment AdjustmentsFive clicks out 20 mm Two clicks outThree clicks out 12 mm Four clicks out 16 mmPrinthead Pressure Ribbon Break Shaft Technical Data Data Interfaces Accessories and OptionsSensors ControlsTTR High Gloss Polyester Media SpeciﬁcationsDirect Thermal Media TTR Premium BoardCore Media Roll SizeRoll Non-Adhesive Strip MediaMinimum 23.8 mm Media,Self-Adhesive Strip ⇒ Media Width including liner Maximum 114.3 mmInches 12 mm 16 mm 20 mm Self-Adhesive LabelsMaximum Depends on Dram size Minimum Inches Following distances from the inner edge of the mediaFive ﬁxed positions distance from inner edge of the media Tickets with GapMin. length between slots Max. length between slots Depends on Dram sizeMark Tickets with Black MarkMaximum Depends on Dram size Minimum 20.0 mm Inches Common 12.5 mm Inches MinimumTransfer Ribbons Sensitivity Number Media or Ribbon Setting the Media Sensitivity Number,Type the following command lines and press Enter Where SIg1,567 sets the media sensitivity number toSetting Direct Thermal Media Setting the Media Sensitivity Number,Direct Thermal Media Sensitivity Settings Thermal Transfer Media and Ribbon Sensitivity SettingsInterfaces Default Communication SetupRS-232 Interface Board Interface Cable ConnectorsPin Signal Name IeeeEasyLAN 100i Interface Board Supported IPL-3 Commands Supported IPL-3 Commands, Supported IPL-3 Commands, ESCu SIF