Manuals / Intermec / Computer Equipment / Barcode Reader

Intermec F4 manual Sif, ESCu

Models: F4

1 83

Download 83 pages 42.04 Kb

Page 82

	Appendix 4 Supported IPL-3 Commands
Supported IPL-3 Commands, cont.
IPL Command	Syntax
Test and Service Mode, Exit	R
Top of Form, Set	<SI>F
Transmissive Sensor Value, Transmit	G
User-Deﬁned Characters (UDC) and Graphics, Print	g
User-Deﬁned Character, Clear or Create	G
User-Deﬁned Character Field, Create or Edit	U
User-Deﬁned Characters, Transmit	<ESC>u
User-Deﬁned Font Character, Create	t
User-Deﬁned Fonts, Print	t
Warm Boot	<BS>
Width of Line, Box, Bar, or Character, Deﬁne	w

Intermec EasyCoder F4 – Installation & Operation IPL Version, Ed. 3

81

Image 82

Intermec F4 manual Sif, ESCu

Contents

EasyCoder F4 Bar Code Label Printer Contents Contents, Appendix Ministère des Communications du Canada FCC Notice United States of AmericaDOC Notice Canada Canadian Dept. of Communication GS Notice GermanyEasyCoder F4 Declaration of Conformity89/336/EEC and 73/23/EEC Description IntroductionChapter Safety Precautions Voltage range. It also contains various signs of approvalInstallation UnpackingFront View Rear View Media Compartment Media Compart- ment, Media Supply Positions Print Mechanism Omitted in dedicated direct thermal printing modelsPower Computer ConnectionsControls and Indicators Control Lamps DisplayKeyboard BeeperSwitching On Starting UpMedia Load Tear-OffTear-Off, Media is guided with a minimum of play Pull downwards Tear-Off with Quick-Load Tear-Off with Quick-Load, Peel-Off Self-stripPeel-Off, Insert the start of the liner under the lip Peel-Off, There is no need to remove the media supply roll post External SupplyStraight-through printing-preferably with Quick-Load Quality or cause unnecessary wear to the printheadThermal Transfer Printing Ribbon LoadRibbon Load, Setting Up the Printer Ribbon Load, Test/Service Setting Up the PrinterDescription Default Setup CommunicationData Bits Serial CommunicationBaud Rate ParityPrinthead hot Label at strip pin Label skipping Setup Parameters,Serial Communication, Protocol PrintingSerial Communication, Protocol, ReadyTest/Service TestprintTest/Service, Paper Type MediaMedia Type Label LengthMedia, Darkest. Default value is 0%Darkness Entering Setup Mode At Installation Setup ModeNavigating in Setup Mode Setup Mode Overview, Part From previous Press Setup to exit the Setup Mode Options IntroductionIntegral Liner Takeup Unit DTP ModelInch Adapter Quick-Load Guides Label Taken Sensor Interface Boards Troubleshooting Symptom Possible Cause Remedy Refer toMaintenance Printhead CleaningPrinthead Cleaning, Remove any media and transfer ribbonPrinthead Cleaning, External Cleaning Cleaning the Media Guides Printhead Replacement Printhead Replacement, Printhead Replacement, Adjustments Narrow Media AdjustmentFour clicks out 16 mm Two clicks outThree clicks out 12 mm Five clicks out 20 mmPrinthead Pressure Ribbon Break Shaft Technical Data Controls Accessories and OptionsSensors Data InterfacesTTR Premium Board Media SpeciﬁcationsDirect Thermal Media TTR High Gloss PolyesterCore Media Roll SizeRoll Media Non-Adhesive Strip⇒ Media Width including liner Maximum 114.3 mm Media,Self-Adhesive Strip Minimum 23.8 mmFollowing distances from the inner edge of the media Self-Adhesive LabelsMaximum Depends on Dram size Minimum Inches Inches 12 mm 16 mm 20 mmMax. length between slots Depends on Dram size Tickets with GapMin. length between slots Five ﬁxed positions distance from inner edge of the mediaCommon 12.5 mm Inches Minimum Tickets with Black MarkMaximum Depends on Dram size Minimum 20.0 mm Inches MarkTransfer Ribbons Sensitivity Number Where SIg1,567 sets the media sensitivity number to Setting the Media Sensitivity Number,Type the following command lines and press Enter Media or RibbonThermal Transfer Media and Ribbon Sensitivity Settings Setting the Media Sensitivity Number,Direct Thermal Media Sensitivity Settings Setting Direct Thermal MediaInterfaces Default Communication SetupRS-232 Interface Ieee Interface Cable ConnectorsPin Signal Name BoardEasyLAN 100i Interface Board Supported IPL-3 Commands Supported IPL-3 Commands, Supported IPL-3 Commands, SIF ESCu