Manuals / Intermec / Computer Equipment / Barcode Reader

Intermec F4 manual Interfaces, RS-232 Interface, Default Communication Setup

Models: F4

1 83

Download 83 pages 42.04 Kb

Page 76

Interfaces

RS-232 Interface

RS-232 Port

Appendix 3

The EasyCoder F4 has, as standard, one serial communication interface: RS-232.

Default Communication Setup

Baud rate:	9600
Char. length	8 bits
Parity:	None
Stop bits:	1
Protocol:	XON/XOFF

To change the serial interface settings, see Chapter 6, “Setting Up the Printer.”

Interface Cable
Computer end:	DB-9pin or DB-25pin female connector(PC)
Printer end:	DB-25pin male connector

Host			EasyCoder F4				Host
Signal	DB-9	DB-25		Signal	DB-25	DB-25		Signal
	1	1			1	1		shield
RXD	2	2		TXD	2	3		RXD
TXD	3	3		RXD	3	2		TXD
CTS	8	4		RTS	4	5		CTS
RTS	7	5		CTS	5	4		RTS
		6		DSR	6	20		DTR
GND	5	7		Signal GND	7	7		GND
		16		+ 5V1	16
DSR	6	20		DTR	20	6		DSR
		22		RI	22

1/. The external +5V is limited to 200 mA and is automatically switched off at overload.

Intermec EasyCoder F4 – Installation & Operation IPL Version, Ed. 3

75

Image 76

Intermec F4 manual Interfaces, RS-232 Interface, Default Communication Setup

Contents

EasyCoder F4 Bar Code Label Printer Contents Contents, Appendix FCC Notice United States of America DOC Notice Canada Canadian Dept. of CommunicationMinistère des Communications du Canada GS Notice GermanyEasyCoder F4 Declaration of Conformity89/336/EEC and 73/23/EEC Description IntroductionChapter Safety Precautions Voltage range. It also contains various signs of approvalInstallation UnpackingFront View Rear View Media Compartment Media Compart- ment, Media Supply Positions Print Mechanism Omitted in dedicated direct thermal printing modelsPower Computer ConnectionsControls and Indicators Control Lamps DisplayKeyboard BeeperSwitching On Starting UpMedia Load Tear-OffTear-Off, Media is guided with a minimum of play Pull downwards Tear-Off with Quick-Load Tear-Off with Quick-Load, Peel-Off Self-stripPeel-Off, Insert the start of the liner under the lip Peel-Off, External Supply Straight-through printing-preferably with Quick-LoadThere is no need to remove the media supply roll post Quality or cause unnecessary wear to the printheadThermal Transfer Printing Ribbon LoadRibbon Load, Setting Up the Printer Ribbon Load, Setting Up the Printer Description Default SetupTest/Service CommunicationSerial Communication Baud RateData Bits ParitySetup Parameters, Serial Communication, ProtocolPrinthead hot Label at strip pin Label skipping PrintingSerial Communication, Protocol, ReadyTest/Service TestprintTest/Service, Media Media TypePaper Type Label LengthMedia, Darkest. Default value is 0%Darkness Entering Setup Mode At Installation Setup ModeNavigating in Setup Mode Setup Mode Overview, Part From previous Press Setup to exit the Setup Mode Options IntroductionIntegral Liner Takeup Unit DTP ModelInch Adapter Quick-Load Guides Label Taken Sensor Interface Boards Troubleshooting Symptom Possible Cause Remedy Refer toMaintenance Printhead CleaningPrinthead Cleaning, Remove any media and transfer ribbonPrinthead Cleaning, External Cleaning Cleaning the Media Guides Printhead Replacement Printhead Replacement, Printhead Replacement, Adjustments Narrow Media AdjustmentTwo clicks out Three clicks out 12 mmFour clicks out 16 mm Five clicks out 20 mmPrinthead Pressure Ribbon Break Shaft Technical Data Accessories and Options SensorsControls Data InterfacesMedia Speciﬁcations Direct Thermal MediaTTR Premium Board TTR High Gloss PolyesterCore Media Roll SizeRoll Media Non-Adhesive StripMedia, Self-Adhesive Strip⇒ Media Width including liner Maximum 114.3 mm Minimum 23.8 mmSelf-Adhesive Labels Maximum Depends on Dram size Minimum InchesFollowing distances from the inner edge of the media Inches 12 mm 16 mm 20 mmTickets with Gap Min. length between slotsMax. length between slots Depends on Dram size Five ﬁxed positions distance from inner edge of the mediaTickets with Black Mark Maximum Depends on Dram size Minimum 20.0 mm InchesCommon 12.5 mm Inches Minimum MarkTransfer Ribbons Sensitivity Number Setting the Media Sensitivity Number, Type the following command lines and press EnterWhere SIg1,567 sets the media sensitivity number to Media or RibbonSetting the Media Sensitivity Number, Direct Thermal Media Sensitivity SettingsThermal Transfer Media and Ribbon Sensitivity Settings Setting Direct Thermal MediaInterfaces Default Communication SetupRS-232 Interface Interface Cable Connectors Pin Signal NameIeee BoardEasyLAN 100i Interface Board Supported IPL-3 Commands Supported IPL-3 Commands, Supported IPL-3 Commands, SIF ESCu