Manuals / Brands / Personal Care / Mobility Aid / Invacare / Personal Care / Mobility Aid

Invacare 9758, 9859 ELEVATING LEGREST ASSEMBLY INSTALLATION (FIGURE 4), ADJUSTING THE ELEVATING LEGREST ASSEMBLY (FIGURE 5)

1 28

Download 28 pages, 527.46 Kb

16

F

R

O

N

T

R

I

G

G

I

N

G

S

PROCEDURE 1 FRONT RIGGINGS

ELEVATING LEGREST ASSEMBLYINSTALLATION (FIGURE 4)

6. To release the legrest, push the legrest release

handle toward the inside of the wheelchair

(facing the front of the wheelchair) and swing the

legrest assembly to the outside of the wheelchair.

ADJUSTING THE ELEVATINGLEGREST ASSEMBLY (FIGURE 5)

NOTE: Adjustments to Articulating Legrests and Fixed

Front End Legrests are performed in the same fasion as

the elevating legrest.

1. To adjust the elevating legrest, raise legs until the

desired height is obtained.

2. To reposition legrest to normal position, support leg

with one (1) hand and push release lever downward

with other hand.

3. To adjust the calfpad, turn pad towards the outside of

the wheelchair.

4. Slide the calfpad up or down until the desired position

is obtained.

5. To secure the calfpad, turn the calfpad towards the

inside of the wheelchair.

Phillips Screw

Spacer

Locknut

Bolt and Locknut

Heel Loop

FIGURE 3 - HEEL LOOP REPLACEMENT

1. Place legrest assembly on the outside of the wheel-

chair and install the hinge plates onto the hinge pins

on wheelchair frame (FIGURE 4).

2. Rotate legrest assembly toward the inside of the

wheelchair until it locks in place (FIGURE 4).

NOTE: The footplate will be on the inside of the wheel-

chair when locked in place.

3. Repeat this procedure for other legrest assembly.

4. After seated in wheelchair, adjust footrest to cor-

rect height by loosening the locknut and

sliding the lower footrest assembly tube up or

down until desired height is achieved.

5. Tighten locknut securely.

Slide Tube

Footplate

Release Lever

FIGURE 5 - ADJUSTING THE ELEVATING LEGREST

ASSEMBLY

Calfpad

Calfpad Rotated for

Height Adjustment

FIGURE 4 - ELEVATING LEGREST INSTALLATION

Calfpad

Assembly

Lower

Footrest

Assembly

Bolt and

Locknut

Hinge

Plates Footplate

Legrest Release Handle

Hinge Pins

Contents

Main WARNING TABLE OF CONTENTS TABLE OF CONTENTS SPECIAL NOTES SAFETY SUMMARY SAFETY SUMMARY SAFETY SUMMARY SAFETY/HANDLING OF WHEELCHAIRS STABILITY AND BALANCE COPING WITH EVERYDAY OBSTACLES A NOTE TO WHEELCHAIR ASSISTANTS PERCENTAGE OF WEIGHT DISTRIBUTION FUNCTIONAL REACH FROM A WHEELCHAIR REACHING, LEANING AND BENDING - FORWARD REACHING, LEANING - BACKWARDS TIPPING Step Tube METHOD 1 - WHEELCHAIR WITH STEP TUBE METHOD 2 - WHEELCHAIR WITHOUT STEP TUBE TRANSFERRING TO AND FROM OTHER SEATS STAIRWAYS ESCALATORS? SORRY! FOLDING AND UNFOLDING THE WHEELCHAIR "HAMMOCK OR SLING SEAT" MODELS "HAMMOCK OR SLING SEAT" MODELS 12 P SPECIFICATIONS 13 SAFETY INSPECTION CHECK LIST A F Y SAFETY INSPECTION CHECKLIST TROUBLESHOOTING/MAINTENANCE MAINTENANCE M A E A C E SWINGAWAY FOOTREST HEIGHT ADJUSTMENT (FIGURE 2) SWINGAWAY FOOTREST ASSEMBLY INSTALLATION (FIGURE 1) HEEL LOOP REPLACEMENT (FIGURE 3) PROCEDURE 1 FRONT RIGGINGS ELEVATING LEGREST ASSEMBLY INSTALLATION (FIGURE 4) ADJUSTING THE ELEVATING LEGREST ASSEMBLY (FIGURE 5) FIGURE 3 - HEEL LOOP REPLACEMENT FIGURE 5 - ADJUSTING THE ELEVATING LEGREST ASSEMBLY FIGURE 4 - ELEVATING LEGREST INSTALLATION A R M S FIGURE 3 - USING OR REPLACING FLIP-BACK ARMREST USING OR REPLACING FLIP-BACK ARMREST (FIGURE 3) FIGURE 1 - REMOVING OR REPLACING STANDARD ARMREST REMOVING OR REPLACING STANDARD ARMREST (FIGURE 1) REPLACING THE BACK UPHOLSTERY (FIGURE 2) REPLACING THE SEAT UPHOLSTERY (FIGURE 3) ADJUSTING SEAT WIDTH FOLD DOWN BACK - TRACER TRANSPORT ONLY (FIGURE 1) Page REMOVING/INSTALLING THE REAR WHEELS (FIGURE 1) REPLACING REAR WHEEL HANDRIM (FIGURE 2) REPLACING/REPAIRING REAR WHEEL TIRE/TUBE INSTALLING/REPLACING SIX OR EIGHT-INCH FRONT CASTERS AND FORKS (FIGURE 1) ADJUSTING FORKS (FIGURE 1) REPLACING/REPAIRING FRONT CASTER TIRE/TUBE REPLACING FRONT CASTERS (FIGURE 2) SEAT-TO-FLOOR HEIGHTSPROCEDURE 6 CHANGING SEAT-TO-FLOOR HEIGHT- TRACER EX ONLY (FIGURE 1) NOTE: 6-inch and 8-inch casters require different forks. FIGURE 1 - CHANGING SEAT-TO-FLOOR HEIGHT - TRACER EX ONLY 8-INCH FORK MOUNTING POSITION 6-INCH FORK MOUNTING POSITIONS Top Middle Bottom INSTALLING/ADJUSTING THE ANTI-TIPPERS This Procedure Includes the Following: Installing/Adjusting Anti-Tippers Wheel Lock Adjustment FIGURE 1 - ANTI-TIPPER LENGTH Top Position Anti-tipper Length FIGURE 2 - INSTALLING THE ANTI-TIPPERS WHEEL LOCK ADJUSTMENT (FIGURE 4) ANTI-TIPPERS/WHEEL LOCKSPROCEDURE 7 PROCEDURE 8 OPTIONS INSTALLING THE AMPUTEE ATTACHMENT (FIGURE 1) FIGURE 1 - INSTALLING THE AMPUTEE ATTACHMENT FIGURE 2 - INSTALLING FIXED HEIGHT I.V. ROD INSTALLING THE CARRYING POCKET (FIGURE 3) INSTALLING FIXED HEIGHT I.V. ROD (FIGURE 2) INSTALLING THE SEAT POSITIONING STRAP (FIGURE 4) PROCEDURE 8 Seat Positioning Strap Upholstery Cane FIGURE 5 - INSTALLING/ADJUSTING THE FRONT ANTI-TIPPERS INSTALLING ADJUSTING FLOOR OPTIONS PROCEDURE 8 LIMITED WARRANTY