Create the custom overlay panel using the dimensions shown.
NOTE: The panel must be prepared as shown to allow proper clearance for the door.
29³¹⁄₆₄"
(74.9 cm)
14³³⁄₆₄"
(36.9 cm)
|
|
|
|
|
| 1¹⁄₄" |
|
|
| 1¹⁄₄" | |||||||||
|
|
|
|
| (3.18 cm) |
|
| (3.18 cm) | |||||||||||
|
|
|
|
|
|
|
|
| ³⁄₄" | ³⁄₄" |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
¹⁄₄" |
|
|
|
|
|
|
| (1.91 cm) | (1.91 cm) |
|
|
|
|
|
|
|
| ¹⁄₄" | |
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
(6.35 mm) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| (6.35 mm) |
|
|
|
|
|
|
|
|
| |||||||||||
Cleaning Before Use
After you remove all of the packaging materials, clean the inside of your ice maker before using it. See the cleaning instructions in the “Ice Maker Care” section.
Location Requirements
■To ensure proper ventilation for your ice maker, the front side must be completely unobstructed. The ice maker may be
■Installation of the ice maker requires a cold water supply inlet of ¹⁄₄" (6.35 mm) OD soft copper tubing with a shutoff valve and either a
■Choose a well ventilated area with temperatures above 55°F (13°C) and below 110°F (43°C). Best results are obtained between 70°F (21°C) and 90°F (32°C).
■This unit must be installed in an area sheltered from the elements, such as wind, rain, water spray, or drip.
■When installing the ice maker under a counter, follow the recommended opening dimensions shown. Place electrical and plumbing fixtures in the recommended location as shown.
NOTES:
■Be sure the power supply cord is not pinched between the ice maker and the cabinet.
■Be sure the water supply line is not pinched between the ice maker and the cabinet.
■Be sure the drain line (on some models) is not pinched between the ice maker and the cabinet.
Unpack the Ice Maker
WARNING
Excessive Weight Hazard
Use two or more people to move and install ice maker. Failure to do so can result in back or other injury.
34"
(86.4 cm)
Min.
34¹⁄₂"
(87.6 cm)
Max.
11¹⁄₂"
(29.2 cm)
3¹⁄₂" 9"
(8.9 cm)(22.9 cm)
A
28¹⁄₂"
(72.4 cm)
Removing Packaging Materials
Remove tape and glue from your ice maker before using.
■To remove any remaining tape or glue from the exterior of the ice maker, rub the area briskly with your thumb. Tape or glue residue can also be easily removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.
■Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. Do not use chlorine bleach on the stainless steel surfaces of the ice maker. These products can damage the surface of your ice maker.
B
24"
(60.1 cm)
15"
(38.1 cm)
A. Recommended location for electrical and plumbing fixtures
B. Floor level
■Choose a location where the floor is even. It is important for the ice maker to be level in order to work properly. If needed, you can adjust the height of the ice maker by changing the height of the leveling legs. See “Leveling.”
4
