Operation and Settings
Projecting Image
3 Adjust the zoom ratio (screen size) (when zoom lens is in use)
You can adjust the focus using the AZoomB item of the Lens menu.
If setting for this projector is not completed, refer to AUser Settings MenuB(A Page 33) upon turning on the power and configure the settings accordingly.
Once the basic settings are configured, this projector can be used by simply performing the following operation procedures.
PREPARATION:
● Remove the lens cap. |
● Connect this projector to the computer. (A Page 21, 23) |
1 Set this projector to the standby mode, and |
Main
Image
Setting
Convergence
Lens
Option
host
Logout
Zoom | Focus | Shift |
|
w | + |
| U |
| _ | L | R |
T |
|
| |
|
|
| D |
Test Pattern |
|
| |
OFF |
| OFF | SET |
display the main menu |
● Refer to ATurning On the Main PowerB |
(A Page 25), and steps 4 to 6 of AAssigning a |
● The [STANDBY/ON] indicator lights up in red. |
2 Click the AONB button under the APowerB |
item of the main menu to project the image |
● The power of this projector turns on, and formatting |
is done taking a few minutes. A gray image will be |
displayed during formatting. The projected image |
appears once formatting ends. |
● The [STANDBY/ON] indicator lights up in green. |
|
|
|
|
|
|
|
|
|
|
|
|
| host | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
| user: root | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| Logout |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Main | Power |
|
|
|
|
|
|
|
|
|
| Warning Status |
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Image | ON | OFF | PROJECTION |
|
|
| None |
|
|
|
| |||||||
| Setting |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Convergence | Lamp Mode |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Lens | Both | Lamp1 |
| Lamp2 |
| Auto |
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| Option | Lamp Information |
|
|
|
|
|
| Hide |
|
|
|
|
|
| ||||
|
| Lamp | Status | Time |
|
|
|
|
|
|
|
|
|
|
| ||||
|
| 1 |
| ok | 10h54m |
|
|
|
| OFF |
| ON |
|
|
| ||||
|
| 2 |
| ok | 11h58m |
|
|
|
|
|
|
|
|
|
|
| |||
|
| Signal Status |
|
|
|
|
|
|
| Temperature |
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
| DVI | Rate(Hz) | Pixel H | Pixel V | Link | Lamp |
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
| 1 |
| 60.00 | 2048 | 2400 | Dual | 26.8 deg.C |
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
| 2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Outside |
|
|
|
| |||
|
| 3 |
| 60.00 | 2048 | 2400 | Dual |
|
|
|
| ||||||||
|
|
| 26.3 deg.C |
|
| ||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
| 4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Inside |
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| 34.0 deg.C |
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
NOTE:
●You can also turn on the power by pressing the [OPERATE I/B] button on the projector unit for more than one second.
●The image may flicker for a few seconds immediately after projection starts. This is not a malfunction.
●After the lamp lights up, it takes about 1 minute or longer for the brightness of the video image on the screen to stabilize.
To enlarge the screen size:
Press the AWB (Wide) end of AZoomB
To reduce the screen size:
Press the ATB (Tele) end of AZoomB
NOTE:
●The screen size changes each time you click on the
inner buttons (
/
). (Fine control)
The outer buttons ( 
/ 
) change the screen size when they are depressed. (Coarse control)
4 Adjust the position of the projection screen
You can adjust the focus using the AShiftB item of the Lens menu.
To shift the image upward:
Press the AUB end of AShiftB
To shift the image downward:
Press the ADB end of AShiftB
To shift the image rightward:
Press the ARB end of AShiftB
To shift the image leftward:
Press the ALB end of AShiftB
NOTE:
●When a zoom lens is used, the adjustment range for lens shift is between 0 % to ±50 % in the vertical direction, and between 0 % to ±25 % in the horizontal direction (during
When a short focal length lens is used, the adjustment range for lens shift is between 0 % to ±15 % in the vertical direction, and between 0 % to ±5 % in the horizontal direction (during
●The position changes each time you click on the inner
buttons (
/
). (Fine control)
The image shifts when the outer buttons ( 
/ 
) are depressed. (Coarse control)
●The lens shift feature does not function if the lens mechanism is secured.( A Page 16 ALens Fixation MechanismB)
30