JVC FR-DS100 manual Unpacking, Power Supply, Operation on AC power, Operation on batteries

Unpacking

Check that the following items were supplied with the FR-DS100.

WorldSpace (WS) antenna (1)

AC power cord (1)

Plug adapter (1)

WS specified extension cable (1)

ID number sticker sheet (1) *

*The 16-digit ID number is not the serial number. The ID number is necessary when subscribing to WorldSpace broadcaster services. Using the ID number stickers, keep the ID number of your unit in safe locations where it can be easily found or referred to if necessary. (Refer to page 16.)

Power Supply

A. Operation on AC power

1.When the FR-DS100 is used in an area where the supply voltage is different from the preset voltage, set the voltage selector to the correct position. For more information, refer to “To set the voltage selector” below.

2.Insert the AC power cord firmly and completely into the AC IN jack on the unit.

CAUTIONS:

1.ONLY USE WITH JVC POWER CORD PROVIDED WITH THIS UNIT TO AVOID MALFUNCTION OR DAMAGE TO THE UNIT. REMOVE BATTERIES WHEN USING THE POWER CORD.

2.BE SURE TO UNPLUG THE POWER CORD FROM THE OUTLET WHEN GOING OUT OR WHEN THE UNIT IS NOT IN USE FOR AN EXTENDED PERIOD OF TIME.

B. Operation on batteries

Loading batteries

1. Open the battery cover by pulling it toward you while pressing down on the tabs marked by the arrows.

2. Insert 6 “D” size/R 20 batteries as shown in the diagram below. A similar diagram can also be found on the rear panel of the unit.

* Be careful to insert the batteries with the » and á terminals oriented correctly.

3. Replace the cover.

• LEAKWARNING

=

•

DO

4

USEDNOT

•OR

ORPUT

REMOVEOTHER

USING ANDBATTERY

IN

EXTERNAL

SEE

THETHE

ACCAUSEBATTERY

TYPES-

INSTRUCTIONPOWER.

BATTERIES

PERSONALBACKWARDS,

MIX

1 4

6

3 6

MANUAL.

SIZE,

("D"

MAY

WITH

1 4

INJURY.

5

R20)EXPLODE

3 6

2

1.

WHEN

2

5

1.

5Vx6

5Vx6

5

To set the voltage selector

Before attempting to use this unit, check the voltage selector on the rear panel of this unit to determine if the selected voltage is appropriate for the power supply in your area. If you need to change the setting to match your local power supply, use a screwdriver to turn the arrow mark until it is pointed at the appropriate voltage setting.

	ANTENNA
AC IN
		4	6		5
	EXTERNAL	1	3	2	1.5Vx6
VOLTAGE
SELECTOR	WARNING
230V
127V	• DO NOT PUT BATTERY IN BACKWARDS, MIX WITH
110V	USED OR OTHER BATTERY TYPES-MAY EXPLODE
	OR LEAK AND CAUSE PERSONAL INJURY.
SEE	• REMOVE THE BATTERIES ("D" SIZE, R20) WHEN
	USING THE AC POWER.

• SEE INSTRUCTION MANUAL.

RL

LINE OUT

Removing batteries

1.Open the battery cover as indicated above.

2.Remove the center battery by hooking your finger onto the cusp of the » side of the battery, and pulling outward. The other batteries should then be easily removable.

3.Repeat step 2 with the other row of batteries.

3

	EXTERNAL
1		3 6
	1	4

2 5

1 .5Vx6

2

VOLTAGE SELECTOR

230V

127V

110V

4

CAUTIONS WHEN USING BATTERIES:

When batteries are used incorrectly, it may result in the leakage of chemicals from the batteries or they may explode. If chemicals from the batteries come in contact with your skin, wash them off immediately with water. If chemicals leak onto the unit, clean the unit completely.

The following care should be taken;

•Check that the positive » and negative á terminals of the batteries are oriented correctly and load them as shown in the diagram.

•Do not mix old and new batteries together, or mix different types of batteries.

•Do not try to recharge non-rechargeable batteries.

•Remove the batteries when the unit is not to be used for an extended period of time.