EN 61

Automatic Editing To VCR

2 Perform Random Assemble Editing on Program 1

13 Rewind the tape in the camcorder to the

only. In order to check VCR and camcorder

timing, select the beginning of a scene transition

beginning of the scene you want to edit and press

as your Edit-In point.

PAUSE (9).

3 Play back the dubbed scene.

14 Press VCR REC STBY (79), or manually

If any images from the scene prior to the

engage the VCR’s Record-Pause mode.

transition you chose for your Edit-In point were

15 Press START/STOP on the remote control.

recorded, that means your VCR moves too

Editing proceeds as programmed, right through

quickly from Record-Pause to Record mode.

to the end of the last registered scene.

If the scene you tried to dub starts in progress,

When dubbing is complete, the camcorder

the VCR is slow to start recording.

enters the Pause mode, and the VCR enters its

Adjustment Of VCR/Camcorder Timing

Record-Pause mode.

4 Press R.A.EDIT ON/OFF to make the Random

If you do not register an Edit-Out point, the

tape will be dubbed all the way to the end

Assemble Editing menu disappear, then press

automatically.

MENU. The Menu Screen appears.

If you operate the camcorder during automatic

5 Press + or to select “t”, and press SET/

editing, the VCR will enter its Record-Pause

SELECT. The VIDEO Menu appears.

mode and automatic editing will stop.

6 Press + or to select “SYNCHRO”, and press

16 Engage the Stop modes for the camcorder and

SET/SELECT. The value for “SYNCHRO” is

the VCR.

highlighted.

To make the R.A.Edit counter display disappear,

7 Based on the diagnostics performed, you can

press R.A.EDIT ON/OFF on the remote control.

NOTES:

now advance the VCR’s record timing by pressing

+. You can also delay the VCR’s record timing by

Pressing R.A.EDIT ON/OFF on the remote control

pressing .

clears all settings registered during Random

The adjustment range is from –1.3 to +1.3

Assemble Editing.

seconds, in 0.1-second increments.

When the editing cable is connected to the remote

Press SET/SELECT to finish the setting.

control’s PAUSE IN connector during dubbing,

8 Press + or to select “BRETURN”, and press SET/

make sure the remote control is pointed at the

SELECT twice.

VCR’s sensor, and the path between the two is

Now perform Random Assemble Editing

unobstructed.

beginning with step 6 on page 60.

Random Assemble Editing may not function

NOTES:

properly when using a tape including several

duplicated time codes. ( pg. 19)

Before performing actual Random Assemble

 

Editing, do a few Random Assemble Editing trial

For More Accurate Editing

runs to check whether the value you have input is

appropriate or not, and make adjustments

 

Some VCRs make the transition from Record-Pause

accordingly.

to Record mode faster than others. Even if you begin

Depending on the recorder, there may be

editing for the camcorder and the VCR at exactly the

situations where the timing difference cannot be

same time, you may lose scenes you wanted, or find

fully corrected.

that you have recorded scenes you did not want. For

 

a cleanly edited tape, confirm and adjust the timing

 

of the camcorder against your VCR.

 

Diagnosing VCR/Camcorder Timing

1Play back the tape in the camcorder, then point the remote control at the camcorder’s remote sensor and press R.A.EDIT ON/OFF.

Random Assemble Editing Menu appears.

Program 1

ADVANCED FEATURES

I N

OUT MODE

1 – – – – : – –

~

2~

3~

4~

5~

6~

7~

8~

T I ME CODE

– : – –

TOTAL

0 0 : 00

Random Assemble Editing Menu

Page 61
Image 61
JVC GR-DVP10 For More Accurate Editing, Automatic Editing To VCR, Diagnosing VCR/Camcorder Timing, Pause, Select twice