
Power |
| NOTES: | |
|
| ● It is recommended that only genuine JVC batteries are | |
This camcorder’s | used in this camcorder. Using generic | ||
choose the most appropriate source of power. Do not use | can cause damage to the internal charging circuitry. | ||
● If the protective cap is attached to the battery pack, remove | |||
provided power supply units with other equipment. | |||
it first. | |||
|
| ||
Charging The Battery Pack | ● During charging, the camcorder cannot be operated. | ||
● Charging is not possible if the wrong type of battery is used. | |||
|
| ||
|
| ● When charging the battery pack for the first time or after a | |
|
| long storage period, the POWER/CHARGE lamp may not | |
Power switch | POWER/CHARGE lamp | light. In this case, remove the battery pack from the | |
|
| camcorder, then try charging again. | |
| Battery pack | ● If the battery operation time remains extremely short even | |
| mount | after having been fully charged, the battery is worn out and | |
|
| needs to be replaced. Please purchase a new one. | |
| Battery pack | ● Since the AC Adapter processes electricity internally, it | |
| becomes warm during use. Be sure to use it only in well- | ||
|
| ||
|
| ventilated areas. | |
|
| ● Using the optional | |
| Arrow | can charge the | |
| pack without the camcorder. However, it cannot be used as | ||
|
| ||
Open the cover. |
| an AC Adapter. | |
To DC | ● After 5 minutes has elapsed in | ||
cassette inserted, the camcorder will automatically turn off its | |||
connector | |||
power supplied from the AC adapter. In this case, the battery | |||
|
| ||
|
| charge starts if the battery is attached to the camcorder. | |
| BATT. RELEASE | Using The Battery Pack |
Perform steps 2 – 3 in “Charging The Battery Pack”.
To AC outlet AC Adapter
1 Set the Power Switch to “OFF”.
2 With the arrow on the battery pack pointing upward, push the battery pack slightly against the battery pack mount a.
3 Slide up the battery pack until it locks in place b.
4
5 Plug the AC Adapter into an AC outlet. The POWER/ CHARGE lamp on the camcorder blinks to indicate charging has started.
6 When the POWER/CHARGE lamp goes out, charging is finished. Unplug the AC Adapter from the AC outlet. Disconnect the AC Adapter from the camcorder.
To detach the battery packSlide the battery pack down slightly while sliding BATT. RELEASE to detach it.Battery pack | Charging time |
|
|
Approx. 1 hr. 30 min. | |
|
|
Approx. 3 hr. | |
|
|
Approx. 5 hr. | |
|
|
Approx. 6 hr. 30 min. | |
|
|
* Provided |
|
Battery pack | LCD monitor on | Viewfinder on |
|
|
|
1 hr. | 1 hr. 10 min. | |
|
|
|
1 hr. 55 min. | 2 hr. 15 min. | |
|
|
|
3 hr. 20 min. | 3 hr. 55 min. | |
|
|
|
4 hr. 35 min. | 5 hr. 20 min. | |
|
|
|
* Provided |
|
|
NOTES:
●Recording time is reduced significantly under the following conditions:
•Zoom or
•The LCD monitor is used repeatedly.
•The playback mode is engaged repeatedly.
●Before extended use, it is recommended that you prepare enough battery packs to cover 3 times the planned shooting time.
ATTENTION:
Before detaching the power source, make sure that the camcorder’s power is turned off. Failure to do so can result in a camcorder malfunction.