JVC HM-DT100U MODE”, LINK”, “S-VHS, “AV COMPU, “POWER SAVE”, JVC TV with AV COMPULINK, When this function is set to “ON”, When this function is set to “ON”

EN 69

*The default setting is bold in the table below.

L“POWER SAVE” When this function is set to “ON”, you can reduce the power consumption. While the

“ON”	VCR is turned off, the front display panel does not show the clock.
“OFF”	When this function is set to “ON”, an i.LINK device cannot be recognized. As a result, it
	is not possible to record a program using the digital tuner’s* timer function. In addition
	the device does not pass along data if it is in a branched connection.
	*For details of a digital tuner, refer to the instruction manual of the digital tuner.
	NOTE:
	It takes some time until VCR completes its set up when you turn on the VCR.

L“S-VHS MODE” You can determine which recording mode - either S-VHS mode or VHS mode - is used

“ON”	for recording on D-VHS and S-VHS tapes.
“OFF”	When this function is set to “ON”, you can record on D-VHS and S-VHS tapes with S-
	VHS picture quality.
	When this function is set to “OFF”, you can record on D-VHS and S-VHS tapes with
	VHS picture quality.

NOTES:

•To record in S-VHS/VHS mode on D-VHS tape, press [D-VHS] to turn off the [D-VHS] indicator.

•S-VHS mode allows you to make high quality video recordings with horizontal resolution of 400 lines, comparing with the 230 lines of resolution of conventional VHS recordings. To achieve the highest quality picture we recommend to record in S-VHS mode. (But remember that a conventional VHS VCR without SQPB cannot play back S-VHS tapes recorded in S-VHS mode.)

•S-VHS MODE setting does not affect recording on VHS tapes. Recording on VHS tapes is always performed in VHS mode except when using S-VHS ET mode (A page 70).

L“AV COMPU- The [REMOTE PAUSE/AV COMPULINK] terminal on the rear panel can be used as

LINK”	either the [REMOTE PAUSE] terminal or the [AV COMPULINK] terminal.
“ON”	When this function is set to “ON”, you can use this terminal as the [AV COMPULINK]
“OFF”	terminal.
	By connecting other JVC’s [AV COMPULINK] components (see the diagram below),
	including amplifiers (or receivers) and televisions, one touch control of the audio and
	video components linked via their [AV COMPULINK] connectors becomes possible.
	For example : simply load a cassette in the VCR and press [PLAY (I)] so that the
	[AV COMPULINK] components automatically turn on, the TV’s AV
	mode is selected and the VCR starts playback. (You do not have to
	press [PLAY (I)] if the cassette’s record safety tab is removed.)
	When this function is set to “OFF”, you can use this terminal as the [REMOTE PAUSE]
	terminal (A page 83).

NOTES:

•When the remote control code is set to C or D, the connector cannot be used as [AV

COMPULINK] terminal even if “AV COMPU-LINK” is set to “ON”. It is recommended to set the remote control code to A when you use this function. (A page 86)

•Connection varies depending on the type of JVC TV you have. Refer to the TV’s instruction manual when making this connection.

JVC TV with AV COMPULINK This VCR

To AV COMPULINK (VCR ONLY)

i.LINK IN/OUT	HDMI OUT OPTICAL
DV IN
S400
D-THEATER	PCM/STREAM
REGION 1
	DIGITAL AUDIO OUT

To Audio in

To S-video in

To [S VIDEO OUTPUT]

S-video cable (supplied)

Audio cable (supplied)

Mini-plug cable (not supplied)

	S-VIDEO	S-VIDEO		ATSC IN
				VHF/UHF
	VIDEO		VIDEO	ANTENNA
Y				IN
PB/CB	L		L
	AUDIO		AUDIO	CABLE BOX
PR/CR	R		R	OUT
COMPONENT		L-1	L-2	ANTENNA
	OUTPUT	INPUT		PAUSE/
VIDEO OUT
				AV

To	To [REMOTE
[AUDIO	PAUSE/AV
OUTPUT]	COMPULINK]