JVC HR-J268EU, HR-J468EU Language Code, Via an RF cable only RF connection, This, Connection

3

SELECT LANGUAGE

Press OK. The Language Set display appears on the front display panel and/or on the screen.

If you are referring to the front display panel

Press %Þ to select your language code.

Language Code
ENGLISH	: 01	NORSK	: 08
DEUTSCH	: 02	SUOMI	: 09
FRANCAIS	: 03	DANSK	: 10
ITALIANO	: 04	POLSKI	: 11
CASTELLANO : 05		E TINA	: 12
NEDERLANDS : 06		MAGYAR	: 13
SVENSKA	: 07
(Ex.) DEUTSCH is selected for SUISSE
International telephone			Language code
country code

		EN	5
5	CONFIRM/SET VIDEO CHANNEL
	If you have connected the video recorder to your TV
	via an RF cable only (RF connection)
	The channel that is shown on the display panel is your
	Video Channel.
	To view picture signals from the video recorder, set
	your TV to the Video Channel. — Refer to the
	instructions supplied with your TV set for how to do
	this.
	● If you have selected MAGYARORSZAG (36), CESKA
	REPUBLIKA (42), POLSKA (48) or OTHER EASTERN
	EUROPE (EE) in step 2 on page 4, "2OUT" appears in
	stead of "1OUT".
	If you have connected the video recorder to your TV
	via both an RF cable and a 21-pin SCART cable (AV
	connection)
	You do not need the video channel so you have to set
	the video channel to off.

If you are referring to the on-screen display

Press %Þ to move the highlight bar (pointer) to the language of your choice.

NÄCHSTE SEITE

NORSK

SVENSKA

NEDERLANDS

CASTELLANO

ITALIANO

FRANCAIS

DEUTSCH

ENGLISH

[5°] =

[MENU] : ENDE

(Ex.) DEUTSCH is selected

Press TV PROG – until the display panel shows

"1OUT– –" to set the Video Channel to off.

To view picture signals from the video recorder, set

your TV to its AV mode. — Refer to the instructions

supplied with your TV set for how to do this.

FINISH AUTO SET UP

4

PERFORM AUTO SET UP

Press OK.

If you are referring to the front display panel

Press %Þ to select "Auto" and press OK or #.

If you are referring to the on-screen display

Press %Þ to move the
highlight bar (pointer) to
"AUTO SET" and press OK	AUTO SET
or #.	T-V LINK

[5°] =

[MENU] : EXIT

"Auto" blinks on the display panel; do NOT press any button on the recorder or remote control until the display panel shows either the display as illustrated in step 5 or "– –:– –".

●If you are using the on- screen display, the

AUTO SET screen will			AUTO SET
appear. As Auto Set Up			PLEASE WAIT
progresses, the "	"
mark on the screen		0	+	+	+
moves from left to right.
		[MENU] : EXIT
	Beginning
					End

6	Press OK and refer to page 7 to check the results.
		● If "– –:– –" appears on the display panel, refer to
		page 7.

NOTES:

●Auto channel set function takes place first; it assigns automati- cally all receivable stations in your area.

●Auto clock set function sets the clock automatically by reading the clock setting data from a station transmitting a PDC signal while auto channel set is being performed.

●During auto channel set, the recorder recognizes each station name of the detected stations and stores them in the recorder's memory, then automatically sets SHOWVIEW assigned Guide Program number for those stations according to the broadcast area.

●In the area where no TV station transmits a PDC signal, the recorder can perform neither auto clock set nor auto Guide Program number set.

●For RF connection users: The video recorder detects the channels which are not occupied by local stations and selects one channel automatically for your Video Channel that is located in the middle of more than 5 vacant channels.

●If there is a power cut, or if you press or MENU while Auto Set Up is in progress, Auto Set Up will be interrupted; be sure to turn off the recorder power once and try again from step 1.

●Auto clock may not function properly depending on the reception condition.