– Timer Recording –
Express Timer Programing
●Remember, the clock must be set before you can program the timer.
●Load a cassette with the record safety tab intact. The recorder turns on, and the counter is reset, automatically.
●Select the appropriate colour system with “PAL/MESECAM” and “NTSC” in Function settings.
BAccess Program Check screen
Press ".
CAccess Program screen
Press " again. Each time you press ", the next program’s Program screen appears.
PR START | STOP | CH | DATE | |
1 | 8:00 | 10:00 | 3 | 24.04 |
2 | 10:00 | 10:45 | 2 | 25.04 |
3 | 11:30 | 13:00 | 1 | 25.04 |
4 |
|
|
|
|
5 |
|
|
|
|
6 |
|
|
|
|
7 |
|
|
|
|
8 |
|
|
|
|
[ | ] : NEXT |
|
| |
| START | – P1 – | STOP |
|
|
|
| ||
| 8:00 |
| 10:00 |
|
|
|
| SP |
|
| DATE |
| TV PROG | |
24.043
[ 
] : NEXT
APress PROG on the remote control to access the
B Press |
|
|
| – P1 – | |
or PR+/– repeatedly to enter the start | START | STOP | |||
21:00 | |||||
time, stop time, date or channel. | |||||
|
|
| SP | ||
● Press and hold START+/– or |
|
|
| ||
DATE | TV PROG | ||||
STOP+/– to increase the time in | |||||
– | – – | ||||
|
|
| |||
|
| ||||
[PROG] : EXIT |
| ||||
● To set the tape speed, press SP/LP/ |
|
|
|
| |
EP (p).
● To
At the programme check screen...
When the weekly serials are programmed, a day of the week appears. When the daily serials are programmed, “DAILY” appears.
CPress OK or PROG.
●If “PROGRAM OVERLAPPED” appears, see “Program overlap warning display”.
DPress #. The recorder turns off automatically and “#” is displayed on the display panel.
NOTE:
●If the tape reaches its end during timer recording, the recording stops and “#”, “” and “$” on the front display panel blink.
To use the recorder while it is in timer recording standby mode
Press #, then press 1. After you use the recorder, press # again to put the recorder into timer recording standby mode.
Checking, canceling or changing program settings
ADisengage timer
DCancel or change program setting
To cancel a program, press & when the Program screen you do not want is shown.
To change a program, press the appropriate button:
EReturn to normal screen
Press " repeatedly until no Program screen is shown.
FReengage timer recording standby mode
Press #. The recorder turns off automatically and “#” is displayed on the display panel.
●When “AUTO TIMER” is set to “ON”, the timer recording standby mode automatically resumes when you turn off the recorder.
Program overlap warning display
If “PROGRAM OVERLAPPED” appears, you have another program overlapping the program you have just made. The Program Check screen appears and conflicting programs will start blinking.
PR START STOP CH DATE
18:00 10:00 3 24.04
PROGRAM OVERLAPPED | 2 | 10:00 | 10:45 | 2 | 25.04 | ||
| 3 | 11:30 | 13:00 | 1 | 25.04 | ||
| 4 | 9:00 | 10:00 | 92 | DAILY | ||
| 5 |
|
|
|
|
|
|
| 6 |
|
|
|
|
|
|
| 7 |
|
|
|
|
|
|
| 8 |
|
|
|
|
|
|
| [ | / ] |
|
| [PROG] : EXIT | ||
|
|
|
|
|
|
|
|
Example:
Program 1 (you have just made) and Progr am4 overlap each other.
A Select program to modify
Press rt, then press e.
● You can only select one of the overlapping programs.
● If you do not mind this overlap, press
PROG to finish the timer program setting. The program starting earlier or
program with the lower program number will be recorded.
B Cancel or change program setting |
| – P1 – | ||
To cancel a program, press & when the | START | STOP | ||
9:00 | 10:00 |
| ||
Program screen you do not want is shown. |
| SP | ||
To change a program, press the | DATE | TV PROG | ||
appropriate button: | 25.04 | 92 |
|
|
| [ ] : DELETE |
|
| |
[PROG] : EXIT |
|
|
| |
when the Program screen on which you |
|
|
|
|
want to make changes is shown, then press OK.
●If the overlap is not yet solved, the conflicting programs will be shown on the Program check screen. Repeat the above steps again.
Press #, then press 1.
●When “AUTO TIMER” is set to “ON”, you do not have to press
#.
