EN 37
C Whenother programs overlap each
If “PROGRAM NOT COMPLETED PROGRAM OVERLAP” appears, you have another program overlapping the program you have just made.
The Program Check screen appears and conflicting programs will start blinking.
| PR START | STOP | CH | DATE | |
PROGRAM NOT COMPLETED | 1 | 8:00P | 11:00 | 12 | 12/24 |
2 | 10:00A | 10:45 | 40 | 12/25 | |
PROGRAM OVERLAP | 3 | 11:30P | 1:00 | 125 | 12/25 |
4 | 9:00P | 10:00 | 10 | 12/24 | |
| 5 |
|
|
|
|
| 6 |
|
|
|
|
7
8
(5,°), THEN (>) (PROG.) : END
EX. Program 1 (you have just made) and Program 4
overlapeachother
1 Confirm overlapping programs
Overlapping programs blink on the screen.
2 Select program to modify
Press SHUTTLE PLUS %Þ, then press SHUTTLE PLUS #.
•You can only select one of the overlapping programs.
NOTE:
If you do not mind this overlap, press PROG. to finish the timer program setting. See “ATTENTION” to the right. Without doing anything for about 1 minute, the VCR will finish the timer programing.
3 Cancel or change program setting
ATTENTION
If there is a conflict in the timer schedule and one program overlaps with another, only the parts shown below in gray will be recorded.
Pattern 1: The program with the lower program number will be recorded.
10:00 | 11:00 | 12:00 | |||||
Program 1 |
| CH10 |
|
|
|
| |
Program 2 |
|
|
|
|
|
| Not recorded |
|
| CH40 |
|
|
| ||
Pattern 2: The program starting earlier will be recorded.
10:00 11:00 12:00
Program 1 |
| CH10 |
|
|
| |||||
|
| Program 2 |
|
|
| Not recorded | ||||
Pattern 3: | CH40 |
|
| |||||||
The program starting earlier will be | ||||||||||
|
| recorded, followed by the remaining portion | ||||||||
|
| of the other program. |
|
|
| |||||
10:00 | 11:00 |
|
|
| 12:00 |
| ||||
Program 1 |
|
| CH10 |
|
|
| ||||
|
|
| Program 2 |
|
|
|
|
|
| |
|
|
|
|
|
|
| CH40 | |||
Not recorded
Tocancelaprogram, press CANCEL when the Program screen you do not want is shown.
“PROGRAM COMPLETED” appears on the screen for about 5 seconds, then normal screen appears.
PROGRAM 4
START | STOP |
9:00 PM | = 10:00PM |
DATE | CH |
12/24/00 | 10 SP |
SUN |
|
PRESS (CANCEL) TO CANCEL PRESS (OK) TO CONFIRM PRESS (PROG.) TO END
To change a program, press the appropriate button: START+/Ð, STOP+/Ð, DATE+/Ð, CH+/Ð, and/or SP/ EP when the Program screen on which you want to make changes is shown, then press OK.
“PROGRAM COMPLETED” appears on the screen for about 5 seconds, then normal screen appears.
NOTE:
If the overlap is not yet solved or another overlap occurs with the timer program setting made last after making correction on a program, the conflicting programs will be shown on the Program Check screen again. Repeat the above steps again until the overlap is solved.
37 | 00.1.31, 10:26 AM |
