Other Problems | JVC HR-S6850EU, HR-S6852EU, HR-S6851EU specs

			EN 63

	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
6.	“[” on the front display panel and	● The loaded cassette has had its record	Remove the cassette and cover the hole
	SAT # indicator won’t stop blinking.	safety tab removed.	with adhesive tape, or insert a cassette
			with the record safety tab intact.
		● The end of the tape was reached during	The programme may not have been
		Automatic Satellite Programme	recorded in its entirety. Next time make
		Recording.	sure you have enough time on the tape to
			record the entire programme.

7.	The power shuts off and “[” won’t	● The end of the tape was reached during	The programme may not have been
	stop blinking.	Instant Timer Recording.	recorded in its entirety. Next time make
			sure you have enough time on the tape to
			record the entire programme.

OTHER PROBLEMS
	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1. Whistling or howling is heard from the		● The camcorder’s microphone is too	Position the camcorder so its microphone
	TV during camcorder recording.	close to the TV.	is away from the TV.
		● The TV’s volume is too high.	Turn the TV’s volume down.

2.	When scanning channels, some of	● Those channels have been designated to	If you need the skipped channels, restore
	them are skipped over.	be skipped.	them ( pg. 54).

3.	The channel cannot be changed.	● Recording is in progress.	Press 9 to pause the recording, change
			channels, then press 4 to resume
			recording.

4.	Channel settings that were made	● After the manual settings were made,	Perform manual setting again.
	manually seem to have changed or	Auto Channel Set was performed.
	disappeared.

5.	No channels are stored in the	● The TV aerial cable was not connected	Turn off the recorder once and connect
	recorder’s memory.	to the recorder when Auto Set Up was	the TV aerial cable to the recorder
		performed.	properly, then turn on the recorder again.
			Then perform Auto Set Up again
			( pg. 10).
		● The fully-wired 21-pin SCART cable was	Turn off the recorder once and connect
		not connected between TV and the	the fully-wired 21-pin SCART cable to the
		recorder when Preset Download was	recorder properly, then turn on the
		performed.	recorder again. Then perform Preset
			Download again ( pg. 12).

ATTENTION

This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After checking the cassette, operate the unit as usual.

Image 63

JVC HR-S6850EU, HR-S6852EU, HR-S6851EU specifications Other Problems

Contents

Video Cassette Recorder Safety Precautions Moisture Condensation Front View Connector cover Rear View Front Display Panel ON-SCREEN Display Operating JVC TVs How To Use Connect the recorder to mains Check the contentsSituate the recorder Connect the recorder to TV Select your country Auto Set Up10 EN Turn on the recorder Press rt to select Auto and press OK or e Perform Auto Set UpSelect the language Press rt to select your language code Press rt to select CH - and press OK or e Perform Preset Download12 EN Set the video channel Just Clock Language for the on-screen display 14 EN Access the Main Menu screenAccess the Country Set screen Language Make connections Installing Satellite ControllerSituate the Satellite Controller Attach the Satellite Controller 16 EN Setting satellite receivers brand and channel TV Auto Power On NexTView LinkVCR Auto Standby Direct Rec 18 EN Basic Playback Activate frame-by-frame playback Slow MotionHigh-Speed Turbo Search Pause during playback Skip Search 20 ENVariable Speed Search Index Search Soundtrack Selection Next Function MemoryRepeat Playback Manual Tracking 22 EN Tape Remaining Time Instant Timer Recording ITR Receiving Stereo and Bilingual Programmes Engage the S-VHS ET mode24 EN Super VHS ET S-VHS ET Recording Playback 26 EN Access the Showview screenAccess the Showview Program screen Before performing the Showview Timer Programming Enter the programme title Set the VPS/PDC modeAccess the Title Edit screen Engage the recorder’s timer mode 28 EN Express Timer Programming Press PR+ To Timer-Record Weekly Or Daily SerialsVPS/PDC Recording Enter the channel position Set the programme start/stop time and channel Enter the programme modeBefore performing the 24 Hour Express Timer Programming 30 EN Access the Programme Check screen/display Cancel or change a programmeDisengage the timer mode Return to the timer mode Overlapping programmes blink on the TV screen Cancel or change programme settingConfirm the overlapping programmes Select the programme to modify Before performing the following steps Select the L-2 Select modeRecording mode Programme Recording 34 EN Navigation Select a programme Navigation PlaybackProgramme Navigation Screen Load a recorded cassette 36 EN Edit Programme TitleSelect the programme Example Enter JVC News Entering CharacterDelete Tape Data Delete the tape data 38 EN Edit From a Camcorder Start the source player Set the input mode of recording deckAnother Video Recorder Advantages of S-VHS video recorders Output/Input Set Decoder connector Select and L-2 Input Setting Simple Connections Connecting To a Satellite Receiver Perfect Connections Set the tuner Select the input mode44 EN Connect the decoder Make connections Connecting/Using a Stereo System Select the mode setting Mode SetAccess the Mode Set screen Select the mode System to on or OFF pg When viewing overplayedWhen this function is set to ON, the timer is automatically Disengaged when the recorder is powered back on Function pg , set PROG. Navigation to OFF On the remote control, or press 7 on the recorderEntire programme while timer-recording in SP mode 48 EN Correct vertical vibration in the picture when playing back When this function is set to ON, you can reducePower consumption while the recorder is turned off When this function is set to ON, you can automatically About Ntsc Playback 50 EN Enter the Guide Program number Showview System SetupGuide Program Number Set Guide Program Number Auto Channel Set Access the Auto Channel Set screenTuner Set 52 EN Perform Auto Channel Set View the Confirmation screenPress OK twice Manual Channel Set 54 EN Delete a Channel When Receiving a Scrambled Broadcast 56 EN Set Stations aSet Stations B Station Name TV Station And ID List Access the Clock Set screen Clock Set58 EN Start the clock operation Set the date and timeSet Just Clock Set the source channel position for clock data 60 EN Access the Video Channel Set modeExit the Video Channel Set mode Video Channel Set Power Recording 62 EN Other Problems Playback 64 EN Lines VHS Signal-to-noise ratio 45 dB Horizontal resolutionMemory backup time Approx min Scan system 66 EN Memo Country code International telephone Language code