
EN 23
D Adjusting tracking condition
— Tracking Adjustments Automatic tracking adjustment
This VCR automatically adjusts the tracking condition. Whenever you insert a tape and start playback, automatic tracking starts working and continuously analyzes the signal to enable optimum picture quality during playback.
Manual tracking adjustment
If automatic tracking cannot eliminate noises well during playback, use the manual tracking following the procedures below.
●You can also use the manual tracking during slow motion playback (☞ pg. 29).
1 Activate manual tracking
Press SP/EP on the Remote during playback.
2 Eliminate the noises on the TV screen
Press CH + or – on the Remote.
●Press it briefly for a fine adjustment, or press and hold for coarse adjustment. Watch the screen and continue adjustment until optimum picture and sound quality are achieved.
●To reactivate automatic tracking, press SP/EP on the Remote. The automatic tracking becomes active again.
E Selecting monitor sound
— Audio Monitor
You can select the desired monitor sound.
While playing back a tape on which stereo sound or SAP sound is recorded, press A. MONITOR on the Remote. Each time you press the button, sound changes as follows:
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| NORM |
|
|
|
| NORM | |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
HI-FI: Normally select this.
Hi-Fi sound is played back.
NORM HI-FI:
Both sounds on the
NOTES:
●The above indication appears when “SUPERIMPOSE” is set to “ON” (☞ pg. 39, 40), though the monitor sound changes in sequence.
●If the tape being played back has no
●If RF connection (☞ pg. 7) is used for viewing pictures on the TV, sound will be monaural even though you select
●You can also use the menu to select your desired monitor sound. (☞ pg. 42)
F Automatic operations after
rewinding — Next Function Memory
The Next Function Memory “tells” the VCR what to do after rewinding is complete.
●Ensure that the VCR is in stop mode.
a– For Automatic Playback Start
Press REW ( 1 ), then press PLAY ( 3 ) within 2Ê seconds.
b– For Automatic Power Off
Press REW ( 1 ), then press POWER within 2Ê seconds.
c– For Automatic Timer Standby
Press REW ( 1 ), then press TIMER within 2Ê seconds.
NOTE:
It is not possible to select the Automatic Timer Standby function if the cassette’s record safety tab is removed.
G Locating beginning of
recordings — Index Search
Index codes are placed on the tape at the beginning of each recording when recording on this VCR. You can find and automatically play back from the beginning of any recording using the Index Search function.
1 Start search
While the tape is not running, press SHUTTLE PLUS
4or ¢ on the Remote.
2 Access distant code
To access a recording of 2 to 9 index codes away, press SHUTTLE PLUS 4 or ¢ repeatedly until the correct number is displayed on screen (only if “SUPERIMPOSE” is set to “ON” ; ☞ pg. 39, 40).
Playback begins automatically when the desired recording is located.
Beginning of the current |
|
|
| Current position | Beginning of the 2nd next | ||||||
program recorded |
|
|
|
|
|
| on the tape |
|
| program recorded | |
|
|
|
|
|
|
| |||||
Previous |
|
|
|
|
|
|
| Next |
|
|
|
program |
|
|
|
|
|
|
| program | 2nd | next | |
recorded |
|
|
|
|
|
|
| recorded |
|
|
|
|
| 1 | 2 |
| 3 | ||||||
|
|
|
4 ¢
●If you want to find the very beginning of the desired program, press REW ( 1 ) or FF ( Á ) after playback starts.
NOTE:
An index code is not placed on the tape when recording is resumed from recording pause.