Video Plus+ Timer Programming, Press Prog | JVC HR-S9500EK guide

14BASICOPERATIONS (cont.)

Video Plus+

Timer

Programming

Before performing Video Plus+ Timer Programming:

●Make sure that the recorder's built-in clock is set properly.

●Insert a cassette with the safety tab in place. The recorder will come on automatically.

●Turn on the TV and select the VIDEO channel (or AV mode).

2	1	2		DAILY
2				2
				3
NUMBER	4	5		6
5 PDC	7	8		9	WEEKLY
	7	8		9	7
		0		4


STOP+/–
1,6 PROG	1
				SP/LP	4
					4
			3		OK 3,6

With Video Plus+, timer programming is greatly simplified because each TV programme has a corresponding code number which your recorder is able to recognise.

ACCESS VIDEO PLUS+ SCREEN

1	Press PROG.	VIDEO PLUS+
	Press PROG.

		[0 – 9] =
		[+/–] : EXPRESS PROGRAMING
		[PROG] : EXIT

The front display panel looks like this:

ENTER PLUSCODE NUMBER

	Press the NUMBER keys to	VIDEO PLUS+
	enter the PlusCode	VIDEO PLUS+
	enter the PlusCode	1 2 3 4 5 6 7 8
	2 number of the programme	1 2 3 4 5 6 7 8
	2 number of the programme
	you wish to record.

●If you make a mistake, press and input the

	correct number.	[0 – 9] =
	correct number.	[ ] : DELETE
		[ ] : DELETE
		[PROG] : EXIT

The PlusCode number you enter appears on the front display panel:

The display panel shows only a 4-digit number.

ACCESS VIDEO PLUS+ PROGRAM SCREEN

	Press OK, and the Video				– P1 –
	Plus+ Program screen			VIDEO PLUS+ 123456789
3 appears (if you’re just				START		STOP
3 appears (if you’re just			21:00		= 22:00
	starting out, “P1” appears).			SP	VPS/PDC OFF
				SP	VPS/PDC OFF
	The display panel shows the			DATE		TV PROG
	programme start time.		25.12		1
	Pressing	changes the				BBC 1
	Pressing	changes the
	display to the programme			: OK
	stop time, then the date and
	preset position.

				SP

IMPORTANT

Make sure the preset position number you wish to record is displayed; if not, see "Video Plus+ Setup" on page 56 and set the Guide Program number for that PlusCode number correctly.

●If the number you entered is invalid, "ERROR" appears on the screen and "Err" appears on the display panel. Press and input a valid PlusCode number.

●If the "GUIDE PROG SET" screen appears, see "ATTENTION – Regarding Guide Program Number Set" on page 15.

Image 14

JVC HR-S9500EK setup guide Before performing Video Plus+ Timer Programming, Press Prog, Correct number

Contents

HR-S9500EK Safety Precautions Connection to the mains supply in the United Kingdom Moisture Condensation Do not place the recorder Some Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of TV AV1 OUT switchTo connect to a TV with 21-pin AV input connector Scart Mains outlet Back of Recorder Back of TV Audio in connectorsMains outlet Mains Power Cord Go to item Before performing the following procedure, make sure thatWill appear Beginning Auto Set Up results appear on the display panel If both auto channel set and auto clock set have failed Point PlaybackLoad a Cassette Start Playback Playback Activate HIGH-SPEED Search Recording Engage ITR Mode Select Preset to WatchReset Counter SET Counter Display Press Prog Video Plus+ Timer ProgrammingBefore performing Video Plus+ Timer Programming Correct number Timer Warning PDC Recording Start Time Express Timer ProgrammingBefore performing Express Timer Programming Time Return to Normal SET PDC ModeTimer Mode Screen Check, Cancel And Replace Programmes Recording According To Tape Type VHS Super VHS and VHS S.T. Picture System Playback/ Recording According To Tape Charac- teristicsTurn on the Recorder Or press Record on the recorder RecordingPlayback During B.E.S.T Digital TBC/NR Playback Picture AdjustmentManual Tracking Digital 3R Sections Looking For Scene You WantSkip Over Unwanted Activate Index Search Variable-Speed Search/ Reverse Play Audio signal during TimeScanTimeScan Normal recorder Speed SP Speed LP Audio output TimeScanTimeScan Audio Forward Search Play Slow-Motion Still Soundtrack Selection Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes During Playback Return to Normal Screen Access Main MenuAdjust Audio Activate Spatializer Satellite Receiver Unit Switch SignalAutomatic Satellite Programme Recording Rear panel AV1 OUT Engage Auto Satellite Prog REC Mode Access Mode SET ScreenSelect AV2 Select Mode Before performing the following steps Remote Con- trol Functions TV Multi-brand Remote ControlControl Your TV Using Additional Buttons SET TV Brand Code SET Satellite Receiver Brand Code SET Remote Control CodeRE-SUPPLY Power Operate Satellite Receiver Advantages Of S-VHS Video Recorders Editing Mode SettingMinimizing Picture Degradation While Editing Edit From Camcorder Edit To Or From Another Video Recorder Your recorder AV2 Select SettingTV Receiver Quality S-VHS pictures Load Source Cassette Access R.A. Edit ScreenPrepare for Editing Start Source Playback Start R.A. Edit Locate EDIT-IN PointLocate EDIT-OUT Point END R.A. Edit Insert Editing SET Input ModeReset the Counter Locate END Point END Insert Editing Engage Insert EditingStart Editing END Audio Dubbing Engage Audio DubbingStart Dubbing Audio OUT Information On J Terminal Terminal JLIPJoint Level Interface Protocol ConnectorAccess Initial SET Screen SET Jlip ID Number ENABLE/DISABLE ON-SCREEN Display Access Main Menu ScreenAccess Mode SET Screen Other Functions Auto SP→LP Timer Auto Timer Retake Repeat PlaybackNtsc Playback Next Function Memory Connection To Stereo System Audio Cable not provided Speaker Video Channel Set Access Video Channel SET ModeExit Video Channel SET Mode SET Video Channel With RF Connection Auto Channel Set Tuner SetPerform Auto Channel SET After Scan Completed Screen preset positionsProcedures Is displayed on the screen Information Storing Channels ManuallyEnter NEW Channel Close Confirmation Screen Delete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Close Confirmation Access Manual Channel SET ScreenSelect NEW Station Select Station Name Character TV Station And ID List Station Name TV Station Channel Number Guide Clock Set Just Clock Guide Program Number Set Video Plus+ SetupNumber Questions And Answers Ä remain lit on the display panel. Is there Problem? Connect the mains power cord TroubleshootingNo power is applied to the recorder Timer Recording Won’t stop Spatializer Button enables/disables Spatializer. pg Index Audio OUT L/R Connectors enable Rear View Remote Control How To Use Audio OUT x 1 S-Video connectors in x 1, OUT x DA4 Double Azimuth helical