JVC HR-S9500EK - page 15

SET TAPE SPEED

Press SP/LP ( ) to set the tape speed.

SET PDC MODE

Press PDC to select "ON" or "OFF".

If "VPS/PDC ON" is displayed on the screen or "VPS/

PDC" is lit on the display panel, PDC is set to ON.

If "VPS/PDC OFF" is displayed on the screen or "VPS/

PDC" is not lit on the display panel, PDC is set to OFF.

Z "PDC Recording" in the column below.

●VPS (Video Programme System) recording is not

currently available in the U.K. and not possible with

this recorder.

RETURN TO NORMAL SCREEN

Press PROG or OK. "PROGRAM COMPLETED" appears

on the screen for about 5 seconds, then normal screen

appears.

●Repeat steps 1 – 6 for each additional programme.

ENGAGE RECORDER’S TIMER

MODE

Press ‰ (TIMER). The recorder turns off automatically

and ‰ appears on the display panel.

●To disengage the timer, press ‰ (TIMER) again.

NOTES:

●

To Change The Stop Time . . .

. . . press STOP +/– after pressing OK in step 3. You can

compensate for anticipated programme schedule delays this

way.

●

To Timer-Record Weekly Or Daily Serials . . .

. . . after pressing OK in step 3, press WEEKLY (NUMBER key

“9”) for weekly serials or DAILY (NUMBER key “8”) for daily

serials (Monday – Friday). Either "WEEKLY" or "DAILY"

appears on the screen. Pressing the button again makes the

corresponding indication disappear.

●

You can programme this recorder to timer-record as many as 8

programmes. If you try to programme the recorder to record a

ninth, "PROGRAM FULL" appears on screen and "FULL"

appears on the front display panel. To record the extra

programme, you must first cancel any unnecessary

programmes (

pg. 18).

●

It is not possible to timer-record a TV programme with a

PlusCode number which starts with "0".

ATTENTION

Regarding Guide Program Number Set

"GUIDE PROG SET" appears after performing step 3 if the

Guide Program number for the PlusCode number you

entered has not been set.

●Press the NUMBER keys or %ﬁ to input the preset

position number on which your recorder receives that

station, then press OK or . The Video Plus+ Program

screen appears.

(Ex.) To timer-record a BBC2

programme with Video Plus+.

* If your recorder receives

BBC2 on the preset position

2, press OK or after

entering "2".

Satellite Receiver Users

To timer-record a satellite broadcast using Video Plus+:

1Set "AV2 SELECT" to the appropriate mode. Z pg. 35

2Perform steps 1 – 7.

3Set the satellite receiver to the appropriate channel

before the selected programme begins.

4Leave the satellite receiver's power on.

Now available from some TV stations, PDC (Programme Delivery Control) is a service designed to assure safe, accurate timer

recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals

control your video recorder and have precedence over the advertised times which you may have preset into the timer. This

means that your recorder will start and stop recording when the preset TV programmes actually start and end — even if the

broadcast time of a preset TV programme is changed from what has been advertised. PDC is currently available nationally on

BBC1, BBC2, Ch.4 and Ch.5, except from a few small relay transmitters. Ch.3 operates a PDC service only in a very few areas.

All channels intend to offer this service in due course. Check your TV programme listing guide for latest information. If the

channel you intend to record does not offer a PDC service your recorder will not start recording if PDC has been selected. Be

sure to set PDC to "OFF" if PDC is not available on your selected channel (Z step 5 above).

NOTES:

●

PDC recording is also possible when a satellite receiver or a cable system is connected to AV2 IN on your recorder.

●

PDC recording is also possible via the AV1 IN/OUT connector.

PDC Recording

Timer Warning

– WARNING–

TIMER RECORDING

TO START SOON

[ ]

If you have programmed your

recorder to timer-record a

programme or a series of

programmes, a warning

appears on the screen to tell

you that the recording is due

to start in 5 minutes.

NOTES:

●

The warning only appears if you’re not in the Timer

mode at the time.

●

If this recorder is being used as the player for tape

dubbing, the warning screen will be recorded on the

tape in the other video recorder.

The warning blinks for the entire 5 minutes leading up to

the start of timer recording. To clear the display, press .

GUIDE PROG SET

GUIDE PROG TV PROG

2 – –

[5∞] =

[PROG] : EXIT