JVC HR-VP656U manual Timer again, Has not been programmed correctly Cassette is automatically

							E	N	53
TIMER RECORDING
		SYMPTOM		POSSIBLE CAUSE		CORRECTIVE ACTION
1.	Timer recording won’t work.		● The clock and/or the timer have		Set the clock and/or timer correctly.
			been set incorrectly.
			● The timer is not engaged.		Press TIMER and check to make sure
					that ä appears on the front display
					panel.
			● The VCR has not been set up properly.		Re-perform the set-up procedures.
					Make sure you have compensated for
					Guide Channel and VCR or cable
					box channel number mismatches
					(☞ pg. 38).
2.	Timer programming won’t work.		● Timer recording is in progress.		Timer programming can’t be performed
					when timer recording is in progress.
					Wait until it finishes.
3.	ä and ] on the front display		● The timer is engaged but there’s no		Load a cassette with the record safety
	panel won’t stop blinking.		cassette loaded.		tab intact, or with the hole covered
					with adhesive tape.
4.	The cassette is automatically		● The loaded cassette has had its		Remove the cassette and cover its
	ejected, and ä and ] on the		record safety tab removed.		hole with adhesive tape, or replace it
	front display panel won’t stop				with a cassette on which the safety
	blinking.				tab is intact.
5.	ä blinks for 10 seconds and the		● TIMER has been pressed when there		Check the programmed data and re-
	timer mode is disengaged.		are no programs in memory, or the		program as necessary, then press
			timer record program information		TIMER again.
			has not been programmed correctly.
6.	The cassette is automatically		● The end of tape was reached during		The program may not have been
	ejected, the power shuts off and ä		timer recording.		recorded in its entirety. Next time
	and ]won’t stop blinking.				make sure you have enough time on
					the tape to record the entire program.
7.	Cable channels are not automatically		● The Controller is not properly		Connect the Controller correctly
	switched during timer recording.		connected to the VCR.		(☞ pg. 16).
			● The output channel selected in the		After confirming your cable box’s
			Cable Box Set screen is incorrect.		output channel number, re-access the
					Cable Box Set screen and select the
					correct number (☞ pg. 17).
			● The cable box’s power is off.		Make sure the power is on before
					timer recording starts.
8.	Satellite channels are not automati-		● The Controller is not properly		Connect the Controller correctly
	cally switched during timer		connected to the VCR.		(☞ pg. 19).
	recording.		● The output channel selected in the		After confirming your DBS receiver’s
			DBS Receiver Set screen is incorrect.		output channel number, re-access the
					DBS Receiver Set screen and select
			● The VCR is not set correctly to		the correct number (☞ pg. 20).
			control the DBS Receiver		Set the correct DBS Receiver brand
			● The DBS receiver’s power is off.		code (☞ pg. 21).
					Make sure the power is on before
					timer recording starts.
9.	Timer recording begins as sched-		● Even though you don't use an		Set "CABLE BOX SET" to "OFF"
	uled, but the channel is always		external Cable Box, "CABLE BOX		(☞ pg. 17).
	incorrect.		SET" is set to "ON".
10.We moved, and now VCR Plus+			● The receivable stations in the new area		Re-perform the VCR Plus+ setup
	doesn’t work properly.		are received on different channels than		procedure (☞ pg. 38).
			those in the previous area.
11.	“PROGRAM FULL” is displayed on		● All 8 programs of the VCR’s timer		Wait until a space in memory clears,
	the screen.		memory are used.		or cancel unnecessary program
					information (☞ pg. 42).

CONTINUED ON NEXT PAGE