| 1 | 2 | 3 | NUMBER | "9" |
| 4 | 5 | 6 |
| |
|
|
| 2 |
|
|
NUMBER "8" 7 | 8 | 9 |
|
| |
|
| 0 | 4 | TIMER |
|
CANCEL |
|
|
| ||
|
|
|
|
| |
|
|
| STOP+/– |
|
|
PROG. | 1 |
|
|
|
|
|
|
| SP/EP |
|
|
|
|
| 3 | OK |
|
ATTENTION
If there is a conflict in the timer schedule and one program overlaps with another, only the parts shown below in gray will be recorded.
Pattern 1: The program with the lower program number will be recorded.
10:00 | 11:00 | 12:00 | |||||
Program 1 |
| CH10 |
|
|
|
| |
Program 2 |
|
|
|
|
|
| Not recorded |
|
| CH40 |
|
|
| ||
Pattern 2: The program that is broadcast earlier will be recorded.
10:00 | 11:00 | 12:00 | ||||
Program 1 |
| CH10 |
|
|
|
|
Program 2 |
|
|
| Not recorded | ||
CH40 |
|
| ||||
Pattern 3: The program that is broadcast earlier will be recorded, followed by the remaining portion of the other program.
10:00 | 11:00 | 12:00 | ||
Program 1 |
| CH10 |
|
|
|
| Program 2 |
| CH40 |
|
|
| ||
Not recorded
|
|
|
|
|
| EN |
| 37 |
| |
|
|
|
|
|
|
|
| |||
|
|
|
|
| ||||||
|
| CHECK PROGRAM DATA |
| |||||||
|
| The PlusCode number you |
|
| PROGRAM 1 | |||||
|
| entered and the matching |
| (VCR PLUS+ 12345678) |
| |||||
|
| 5 |
| START | STOP |
| ||||
|
|
| 8:00PM | = 10:00PM | ||||||
|
| tion is displayed on the |
| DATE | CH | |||||
|
| Program screen. Check to | 12/24/98 | 12 SP | ||||||
|
| make sure it’s accurate. |
| THU |
|
|
|
|
| |
|
| PRESS (8=DAILY, 9=WEEKLY |
|
| ||||||
|
|
|
|
| ||||||
|
| ● To change the stop time, | STOP+/– = STOP TIME, SP/EP) |
|
| |||||
|
| PRESS (OK) TO END |
|
| ||||||
|
| press STOP |
| |||||||
|
|
|
|
|
|
|
|
| ||
●To
Pressing the button again makes each corresponding display disappear.
●If you made a mistake, press CANCEL to access the VCR Plus+ screen again and input the correct PlusCode number.
●If the PlusCode number you inputted is incorrect, "ERROR" may appear on the screen to advise you of the error. This happens when the PlusCode number is for a program which has already passed. "ERROR" is displayed for about 5 seconds and the VCR Plus+ screen reappears.
SET TAPE SPEED
6 Press SP/EP.
RETURN TO NORMAL
SCREEN
7 Press PROG. or OK. "PROGRAM COMPLETED" appears on the screen for about 5 seconds, then normal screen appears.
ENGAGE TIMER MODE
8 Press TIMER. The VCR turns off automatically and "ä" is displayed on the display panel.
IMPORTANT
If you have moved to a different area or if a broadcasting station's channel number has been changed, the wrong VCR or CABLE CH number will be displayed on the VCR Plus+ Program screen in step 5. When this happens, set the correct Guide Channel number for that station. (☞ pg. 38, "VCR Plus+ Setup")
NOTES:
●To disengage the timer before recording starts, press TIMER again. Pressing once more
●In case of a power failure after programming, the VCR’s memory backup keeps your selections for approximately 10 minutes.
●When
