JVC LYT1147-001A manual 60 EN, Select Scenes

T I ME CODE – – : – –

TOTAL 00 : 00

I N

1 – – – – : – – ~

2~

3~

4~

5~

6~

7~

8~

OUT MODE

Selected parameter

60 EN USING THE REMOTE CONTROL UNIT (cont.)

Select Scenes

FADE/WIPE

PLAY

NOTES:

● When choosing a scene, set Edit-In and Edit-Out

points so that there is a relatively large difference

between them.

● If the search time for an in-point exceeds

5 minutes, the recording deck’s Record-Standby

mode will be cancelled and editing will not take

EFFECTPAUSE

EDIT IN/OUTR.A.EDIT ON/OFF

CANCEL VCR REC STBY

6Press PLAY (U) and then press R.A.EDIT ON/OFF on the remote control.

The Random Assemble Editing Menu appears.

7 If using a Wipe/Fader at the beginning of the scene, press FADE/WIPE on the remote control. ● Cycle through the

effects by pressing repeatedly, and stop

when the one you want is displayed.

●You cannot use a Picture Wipe/Dissolve at the beginning of Program 1.

8At the beginning of the scene, press EDIT IN/ OUT on the remote control. The Edit-In position appears in the Random Assemble Editing Menu.

9At the end of the scene, press EDIT IN/OUT. The Edit-Out position appears in the Random Assemble Editing Menu.

10If using a Wipe/Fader at the end of the scene, press FADE/WIPE.

●Cycle through the effects by pressing repeatedly, and stop when the one you want is displayed.

●If you select a Wipe/Fader effect for an Edit-Out point, the effect is automatically applied to the following Edit-In point.

●You cannot use a Picture Wipe/Dissolve at the end of the last scene.

●When you use Fader/Wipe effects, that time is included in the total time (this does not apply to Picture Wipe/Dissolve.)

11If using Playback Special Effects, press EFFECT. ( pg. 55)

12Repeat steps 8 through 11 to register additional scenes.

●To change previously registered points, press CANCEL on the remote control. The registered points disappear, one at a time, from the most recently registered point.

●If you are not using Wipe/Fader or Program AE with special effects, repeat steps 8 and 9 only.

place.

● If there are blank portions before or after the Edit-

In and Edit-Out points, a blue screen may be

included in the edited version.

● Since time codes register time only as accurately

as seconds, the time code total time may not

match the total program time exactly.

● Turning off the camcorder’s power erases all

registered Edit-In and Edit-Out points.

● If you select Sepia or Monotone mode from

Program AE with special effects, you cannot use

the Dissolve or Black & White Fader. In this case

the Dissolve or Black & White indicator begins

blinking. Once the next Edit-In point is registered,

the effect is turned off. To combine these effects,

use Sepia or Monotone during recording, then use

the Dissolve or Black & White Fader during

Random Assemble Editing.

● It is not possible to use Wipe/Fader effects and

Program AE with special effects during Random

Assemble Editing using a DV cable.

Picture Wipe And Dissolve Menu (available only for Random Assemble Editing) You can use not only the wipe/fader effects on page 32 but also the picture wipe and dissolve effects below.

DISSOLVE: The new scene gradually appears as the old one gradually disappears.

WIPE – CORNER: The new scene wipes in over the previous one from the upper right corner to the lower left corner.

WIPE – WINDOW: The next scene gradually wipes in from the centre of the screen toward the corners, covering the previous scene.

WIPE – SLIDE: The next scene gradually wipes in over the previous one from right to left.

WIPE – DOOR: The previous scene wipes out from the centre to the right and left, like a door being pushed open to reveal the next scene.

WIPE – SCROLL: The new scene wipes in over the last one from the bottom of the screen to the top.

WIPE – SHUTTER: The new scene wipes in over the previous one from the centre toward the top and bottom of the screen.