JVC LYT1147-001A manual For More Accurate Editing, Automatic Editing To VCR, Pause, Select twice

	EN 61
Automatic Editing To VCR	2 Perform Random Assemble Editing on Program 1
13 Rewind the tape in the camcorder to the	only. In order to check VCR and camcorder
	timing, select the beginning of a scene transition
beginning of the scene you want to edit and press
	as your Edit-In point.
PAUSE (9).
	3 Play back the dubbed scene.
14 Press VCR REC STBY (79), or manually
	● If any images from the scene prior to the
engage the VCR’s Record-Pause mode.
	transition you chose for your Edit-In point were
15 Press START/STOP on the remote control.
	recorded, that means your VCR moves too
Editing proceeds as programmed, right through	quickly from Record-Pause to Record mode.
to the end of the last registered scene.	● If the scene you tried to dub starts in progress,
● When dubbing is complete, the camcorder	the VCR is slow to start recording.
enters the Pause mode, and the VCR enters its	Adjustment Of VCR/Camcorder Timing
Record-Pause mode.
	4 Press R.A.EDIT ON/OFF to make the Random
● If you do not register an Edit-Out point, the
tape will be dubbed all the way to the end	Assemble Editing menu disappear, then press
automatically.	MENU. The Menu Screen appears.
● If you operate the camcorder during automatic	5 Press + or – to select “t”, and press SET/
editing, the VCR will enter its Record-Pause	SELECT. The VIDEO Menu appears.
mode and automatic editing will stop.
	6 Press + or – to select “SYNCHRO”, and press
16 Engage the Stop modes for the camcorder and
	SET/SELECT. The value for “SYNCHRO” is
the VCR.	highlighted.
To make the R.A.Edit counter display disappear,
	7 Based on the diagnostics performed, you can
press R.A.EDIT ON/OFF on the remote control.
NOTES:	now advance the VCR’s record timing by pressing
	+. You can also delay the VCR’s record timing by
● Pressing R.A.EDIT ON/OFF on the remote control	pressing –.
clears all settings registered during Random	The adjustment range is from –1.3 to +1.3
Assemble Editing.	seconds, in 0.1-second increments.
● When the editing cable is connected to the remote	Press SET/SELECT to finish the setting.
control’s PAUSE IN connector during dubbing,	8 Press + or – to select “BRETURN”, and press SET/
make sure the remote control is pointed at the	SELECT twice.
VCR’s sensor, and the path between the two is
	Now perform Random Assemble Editing
unobstructed.
	beginning with step 6 on page 60.
● Random Assemble Editing may not function
	NOTES:
properly when using a tape including several
duplicated time codes. ( pg. 19)	● Before performing actual Random Assemble
	Editing, do a few Random Assemble Editing trial
For More Accurate Editing	runs to check whether the value you have input is
	appropriate or not, and make adjustments
Some VCRs make the transition from Record-Pause	accordingly.
to Record mode faster than others. Even if you begin	● Depending on the recorder, there may be
editing for the camcorder and the VCR at exactly the	situations where the timing difference cannot be
same time, you may lose scenes you wanted, or find	fully corrected.
that you have recorded scenes you did not want. For
a cleanly edited tape, confirm and adjust the timing
of the camcorder against your VCR.

Diagnosing VCR/Camcorder Timing

1Play back the tape in the camcorder, then point the remote control at the camcorder’s remote sensor and press R.A.EDIT ON/OFF.

Random Assemble Editing Menu appears.

Program 1

ADVANCED FEATURES

I N	OUT MODE
1 – – – – : – –	~

2~

3~

4~

5~

6~

7~

8~

T I ME CODE	– – : – –
TOTAL	0 0 : 00

Random Assemble Editing Menu