MENUS FOR DETAILED ADJUSTMENT
ADVANCED FEATURES
EN 27
MasterPage: Advan_Right
this mode, refer to your wide-screen TV’s instruction
manual. During playback/recording on 4:3 TVs/LCD
monitor/viewfinder, the image is elongated vertically.
* Available only when the VIDEO/MEMORY Switch is set to
“VIDEO”.
[OFF]: Disengages the function.
ON : Helps cut down on noise created by wind. The
“” indicator appears. The quality of the sound will
change. This is normal.
SYSTEM
The “s” functions which are set when the Power Switch
is set to “M” are also applied when the Power Switch is
set to “PLAY”.
[ ] = Factory-preset
OFF: Turns off sounds when performing any operations.
It also deactivates the shutter sound effect, however the
shutter sound is recorded onto the tape during Snapshot
for Video Recording (墌pg. 31).
BEEP: The beep sounds when the power is turned on or
off, and at the beginning and end of recording. It also
activates the shutter sound effect. (墌pg. 18, 31)
[MELODY]: Instead of a beep, a melody sounds when
any operation is performed. It also activates the shutter
sound effect. (墌pg. 18, 31)
OFF: Disables the remote control operations.
[ON]: Enables the remote control operations.
OFF: Automatic demonstration will not take place.
[ON]: Demonstrates certain functions such as Program
AE with special effects, etc., and can be used to confirm
how these functions operate. Demonstration starts in the
following cases:
●When the Menu Screen is closed after “DEMO MODE” is
turned “ON”.
●With “DEMO MODE” set to “ON”, if there is no operation for
about 3 minutes after the Power Switch is set to “A” or “M”.
Performing any operation during the demonstration stops
the demonstration temporarily. If no operation is
performed for more than 3 minutes after that, the
demonstration will resume.
NOTES:
●If a cassette is in the camcorder, the demonstration cannot
be turned on.
●“DEMO MODE” remains “ON” even if the camcorder power
is turned off.
●If “DEMO MODE” remains “ON”, some functions will not be
available. After viewing demo, set to “OFF”.
[LCD]: The image is displayed on the LCD monitor when
the viewfinder is pulled out while the LCD monitor is
opened.
FINDER: The image is displayed in the viewfinder when
the viewfinder is pulled out while the LCD monitor is
opened.
EXECUTE: Resets all settings to the factory-preset.
RETURN: Does not reset all settings to the factory-
preset.
CAMERA DISPLAY
●The “n” (CAMERA DISPLAY) settings are effective even
when the Power Switch is set to “A”. However, the menu
settings can be changed only when the Power Switch is set
to “M”.
●The “n” (CAMERA DISPLAY) settings are effective only
for shooting except “BRIGHT”.
[ ] = Factory-preset
墌pg. 9, “Brightness Adjustment Of The Display”
LCD: Keeps the camcorder’s display (except the date,
time and time code) from appearing on the connected TV
screen.
[LCD/TV]: Makes the camcorder’s display appear on
screen when the camcorder is connected to a TV.
OFF: The date/time does not appear.
[AUTO]: Displays the date/time for approx. 5 seconds
when the Power Switch is set from “OFF” to “A” or “M”.
ON: The date/time is always displayed.
●The date indication can also be turned on/off by pressing
the DISPLAY Button on the remote control. (墌pg.17, 34)
[OFF]: Time code is not displayed.
ON: Time code is displayed on the camcorder and on the
connected TV. Frame numbers are not displayed during
recording. (墌pg. 13)
墌pg. 8, “Date/Time Settings”
DSC
[ ] = Factory-preset
[FINE] /STANDARD
The Picture Quality mode can be selected to best match
your needs. Two Picture Quality modes are available:
FINE ( ) and STANDARD ( ) (in order of quality).
NOTE:
The number of storable images depends on the selected
picture quality as well as the composition of the subjects in
the images and the type of memory card being used.
(墌pg. 18)
WIND CUT
BEEP
REMOTE
DEMO MODE
PRIORITY
CAM RESET
BRIGHT
ON SCREEN
DATE/TIME
TIME CODE
CLOCK ADJ.
QUALITY
GR-D94US.book Page 27 Monday, November 17, 2003 2:12 PM