JVC RX-8000VBK manual Release VCR 1 Power, Try to operate your VCR by pressing VCR 1 Power

To change the transmittable signals for operating another manufacturer’s VCR

To change the transmittable signals for operating a DVD player

1.Set the remote control mode to “AUDIO/TV/ VCR.”

2.Press and hold VCR 1 POWER.

3.Press VCR 1.

4.Enter manufacturer’s code (two digits) using

buttons 1–9, and 0.

See the list below to find the code.

Examples: For a JVC product, press 0, 1.

For an NEC product, press 2, 5.

5. Release VCR 1 POWER.

The following button can be used for operating the VCR (with the remote control mode selector set to “AUDIO/TV/VCR”):

VCR 1 POWER Turns on and off the VCR.

After pressing VCR 1 or VCR 1 CONTROL (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on the VCR 1:

CHANNEL +/– Changes the TV channels on the VCR. 1 – 10, 0, 100+ (+10) Selects the TV channels.

	The 100+ (+10) button will function
	as the ENTER button if your VCR
	requires pressing ENTER after
	selecting a channel number.
PLAY	Starts playback.
1	Rewinds a video tape.
`	Fast winds a video tape.
STOP	Stops operation.
PAUSE	Pauses.

ƒREC: Starts recording or enters recording pause.

Notes:

•Refer to the manual supplied with your VCR.

•You can use either VCR 1 button or the VCR 1 CONTROL button to activate the buttons listed above. If you press VCR 1, the playing source also changes. On the other hand, if you press VCR 1 CONTROL, the playing source does not change.

6.Try to operate your VCR by pressing VCR 1 POWER.

When your VCR turns on or off, you have entered the correct code.

If there are more than one code listed for your brand of

VCR, try each one until the correct one is entered.

Manufacturer	Codes	Manufacturer		Codes
JVC	01, 02, 03	PHILIPS	09
EMERSON	11, 26	RCA	05, 06
FISHER	29	SAMSUNG	24
FUNAI	10, 14, 15, 16	SANYO	21, 22, 23
GOLD STAR	12	SHARP	27, 28
HITACHI	04	SHINTOM	30
MITSUBISHI	13	SONY	18, 19, 20
NEC	25	ZENITH	08
PANASONIC	07, 17

Manufacturers’ codes are subject to change without notice. If they are changed, this remote control cannot operate the equipment.

1.Set the remote control mode to “AUDIO/TV/ VCR.”

2.Press and hold VCR 1 POWER.

3.Press DVD.

4.Enter manufacturer’s code (two digits) using

buttons 1–9, and 0.

See the list below to find the code.

Examples: For a JVC product, press 0, 1.

For a SONY product, press 0, 5.

5. Release VCR 1 POWER.

After pressing DVD or DVD MULTI (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on a DVD player:

PLAY:	Starts playing.
4:	Returns to the beginning of the current (or previous)
¢:	track.
	Skips to the beginning of the next track.
STOP:	Stops playing.

PAUSE: Stops playing temporarily. To release it, press PLAY.

After pressing DVD, these buttons

can be used for the DVD menu			CENTER
		2	3
operations.
			MENU
	TEST		REAR-L
Note:	4	5	6
			ENTER

For detailed menu operations, refer to the		REAR-R
	8
instructions supplied with the discs or the
DVD player.

Note:

Refer to the manual supplied with your DVD player.

6.Try to operate your DVD player by pressing one of the above buttons.

•DO NOT forget to turn on the DVD player before pressing one of the above buttons.

Manufacturer	Codes
JVC	01
PANASONIC	02
PHILIPS	07
PIONEER	03
SONY	05
TOSHIBA	04
YAMAHA	06

Manufacturers’ codes are subject to change without notice. If they are changed, this remote control cannot operate the equipment.

51