JVC RX-D201S, RX-D202B manual Turning off the sounds temporarily, Changing the display brightness

Turning off the sounds temporarily

From the remote control ONLY:

Press MUTING to turn off the sound through all connected speakers and headphones.

“MUTING” appears on the display and the volume turns off.

ANALOG AUTO SURR

LR

S.WFR

To restore the sound, press MUTING again.

•Pressing VOLUME +/– (or turning MASTER VOLUME control on the front panel) also restores the sound.

Changing the display brightness

You can dim the display—Dimmer.

Press DIMMER repeatedly.

•Each time you press the button, the display brightness changes as follows:

DIMMER 1: Dims the display.

DIMMER 2: Dims the display more than DIMMER 1.

DIMMER 3: Turns off the display.

(Temporarily canceled when you operate the receiver.)

DIMMER OFF: Cancels the Dimmer (normal display).

Turning off the power with the Sleep Timer

You can fall asleep while listening to music—Sleep Timer.

From the remote control ONLY:

Press SLEEP repeatedly.

•Each time you press the button, the shut-off time changes in 10 minute intervals. The SLEEP indicator lights up on the display.

SLEEP indicator

ANALOG AUTO SURR SLEEP

LR

S.WFR

10min20min30min40min 50min60min OFF (canceled) 90min 80min 70min

When the shut-off time comes:

The receiver turns off automatically.

To check or change the remaining time until the shut-off time:

Press SLEEP once.

The remaining time (in minutes) until the shut-off time appears.

• To change the shut-off time, press SLEEP repeatedly.

To cancel the Sleep Timer:

Press SLEEP repeatedly so that “SLEEP OFF” appears on the display. (The SLEEP indicator goes off.)

•The Sleep Timer is also canceled when you turn off the receiver.

Basic adjustment of auto memory

This receiver memorizes sound settings for each source:

•when you turn off the power, and

•when you change the source.

When you change the source, the memorized settings for the newly selected source are automatically recalled.

The following can be stored for each source:

•Analog/digital input mode (see page 12)

•Bass boost (see page 23)

•Digital equalization pattern (see page 22)

•Input attenuator mode (see page 23)

•Midnight mode (see page 19)

•Speaker output level (see page 22)

•Surround/DSP mode selection (see page 30)

NOTE

If the source is FM or AM, you can assign a different setting for each band.

Signal and speaker indicators on the display

Signal indicators							Speaker indicators
L	C	R						L	C	R
S.WFR		LFE	ANALOG	DUAL MONO		AUTO SURR		S.WFR		LFE
LS	S	RS	DIGITAL AUTO	L	C R	HEADPHONE		LS	S	RS
			LINEAR PCM	S.WFR LFE		PL	x
SB	SB	SB	DIGITAL	LS	S RS	NEO : 6	DSP	SB	SB	SB
			96 / 24			3D-PHONIC
				SB	SB SB
						VIRTUAL SB

The signal indicators light up as follows:

L:• When digital input is selected: Lights up when the left channel signal comes in.

•When analog input is selected: Always lights up.

R:• When digital input is selected: Lights up when the right channel signal comes in.

•When analog input is selected: Always lights up.

C:Lights up when the center channel signal comes in. LS: Lights up when the left surround channel signal comes

in.

RS: Lights up when the right surround channel signal comes in.

S:Lights up when monaural surround signal comes in. SB: Lights up when the surround back channel signal

comes in.

LFE: Lights up when the LFE channel signal comes in.

The speaker indicators light up as follows:

•The subwoofer indicator ( S.WFR ) lights up when “SUBWOOFER” is set to “SUBWFR <YES>.” For details, see page 17.

•The other speaker indicators light up only when the corresponding speaker is set to “SML (small)” or “LRG (large),” and also when required for the current playback.

14