JVC RX-D411S manual Turning off the power with the Sleep Timer, Making sounds natural

Turning off the power with the Sleep Timer

You can fall asleep while listening to music—Sleep Timer.

From the remote control ONLY:

Press SLEEP repeatedly.

•Each time you press the button, the shut-off time changes in 10-minute intervals. The SLEEP indicator lights up on the display.

SLEEP indicator

10min = 20min = 30min = 40min =50min = 60min = 70min = 80min =90min = OFF (Canceled) = (Back to the beginning)

When the shut-off time comes:

The receiver turns off automatically.

To check the remaining time until the shut-off time:

Press SLEEP once.

The remaining time (in minutes) until the shut-off time appears.

•To change the shut-off time, press SLEEP repeatedly.

To cancel the Sleep Timer:

Press SLEEP repeatedly so that “SLEEP OFF” appears on the display. (The SLEEP indicator goes off.)

•The Sleep Timer is also canceled when you turn off the receiver.

Making sounds natural

JVC’s CC (Compression Compensative) Converter eliminates jitter and ripples, achieving a drastic reduction in digital distortion by processing the digital music data in 24 bit- quantization and by expanding the sampling frequency to 176.4 kHz (for fs 44.1 kHz signals)/192 kHz (for fs 48 kHz signals) on the front speakers.

By using the CC Converter, you can obtain a natural sound field from both digital and analog sources.

•Once you have made an adjustment, it is memorized for each source.

Press CC CONVERTER repeatedly.

•Each time you press the button, the mode changes as follows:

CCCNVRTR 1 Select when playing back an analog source or a digital source with non compressed digital sound signal (Linear PCM).

The CC CONVERTER 1 indicator lights up on the display.

CCCNVRTR 2 Select when playing back a source with compressed digital sound signal (Dolby Digital or DTS).

The CC CONVERTER 2 indicator lights up on the display.

CCCNVRTR OFF Select when not using the CC Converter.

Basic adjustment of auto memory

This receiver memorizes sound settings for each source:

•When you turn off the power

•When you change the source

When you change the source, the memorized settings for the newly selected source are automatically recalled. The following can be stored for each source:

•Video input setting (see page 21)

•Audio input setting (see page 21)

•CC Converter (see the left column)

•Midnight mode (see page 33)

•Digital equalization patterns (see page 36)

•Bass Boost (see page 37)

•Input attenuator mode (see page 37)

•Surround/DSP mode selection (see page 44)

NOTE

If the source is “FM” or “AM,” you can assign a different setting for each band.

Signal and speaker indicators on the display

Signal indicators Speaker indicators

The signal indicators light up as follows:

L:• When digital input is selected: Lights up when the left channel signal comes in.

•When analog input is selected: Always lights up.

R:• When digital input is selected: Lights up when the right channel signal comes in.

•When analog input is selected: Always lights up.

C:Lights up when the center channel signal comes in.

LS:	Lights up when the left surround channel signal
	comes in.
RS:	Lights up when the right surround channel signal
	comes in.

S:Lights up when monaural surround signal comes in.

SB:	Lights up when the surround back channel signal
	comes in.
LFE:	Lights up when the LFE channel signal comes in.

NOTES

•When “A MULTI” is selected for the audio input setting (see page 21), all the signal indicators except “SB” and “S” light up.

•When playing back multi-channel digital sound recorded in DVD- Audio with HDMI connection (see pages 9 and 21), the signal indicators may not light up correctly.

The speaker indicators light up as follows:

•The subwoofer indicator () lights up when “SUBWOOFER” is set to “YES.” For details, see page 30.

•The other speaker indicators light up only when the corresponding speaker is set to “SML (small)” or “LRG (large),” and also required for the current playback.

23