JVC RX-DP20VSL Dimmer Much dimmer, Canceled, connected, On the unit, On the unit, On the unit, Press DIMMER, Muting the Sound, 1. Press TAPE/MD, On the unit ONLY:

Muting the Sound

Making Sounds Natural

From the remote control ONLY:

Press MUTING to mute the sound	MUTING
Press MUTING to mute the sound
through all speakers and headphones
connected.

“MUTING” appears on the display and the volume turns off (the VOLUME level indicator goes off).

	ANALOG	SPEAKERS	1
L	R

SUBWFR

Ex. When the source is “VIDEO.” The VOLUME level indicator goes off.

To restore the sound, press MUTING again so that “MUTING OFF” appears on the display for a while.

•Turning MASTER VOLUME on the unit or pressing VOLUME +/– on the remote control also restores the sound.

Turning Analog Direct On and Off

You can enjoy the sound quality closer to the original source by skipping the sound adjustments such as Parametric Equalizer (see page 42) and Midnight mode (see page 43). You can only adjust the volume level while Analog Direct is in use.

•You have to make this setting for each analog source.

Press ANALOG DIRECT.

•Each time you press the button, Analog Direct turns on and off.

–When Analog Direct turns on, “ANALOG DIRECT” appears in the main display.

ANALOG	ANALOG DIRECT
DIRECT

	On the unit	From the remote control
(inside the front door)


ANALOG		SPEAKERS 1
L	R

SUBWFR		VOLUME

Ex. When the source is “VIDEO.”

Notes:

•This function is applied only to the analog sources.

•Activating one of the Surround/THX/DSP modes will cancel Analog Direct automatically.

•If you turn on Analog Direct, the following settings are canceled temporarily—Surround/THX/DSP modes (pages 45 and 52), Input Attenuator (see page 22) and CC Converter, speaker output level (page 32), Parametric Equalizer (page 42), and Midnight mode (page 43).

Turning off Analog Direct activates the above settings except the speaker output level settings.

•If you turn off Analog Direct while listening to an analog source, muting time* will be a little longer. (* The period during which no sound comes out.)

JVC’s CC (Compensative Compression) Converter eliminates jitter and ripples, achieving a drastic reduction in digital distortion by processing the digital music data in 24 bit–quantization and by expanding the sampling frequency to 128 kHz (for fs 32 kHz signals)/176.4 kHz (for fs 44.1 kHz signals)/192 kHz (for fs 48 kHz signals). By using the CC Converter, you can obtain a natural sound field from both digital and analog sources.

Press CC CONVERTER so that the CC CONVERTER lamp lights up.

•Each time you press the button, CC Converter turns on and off (the lamp goes off) alternately.

CC CONVERTERCC CONVERTER

On the unit

From the remote control

Notes:

•You cannot use this function while Analog Direct or THX mode is in use. If you turn on Analog Direct or THX mode while this function is in use, this function will be canceled temporarily.

•This function does not work for the surround back channel when the source is “EXT 7.1CH.”

Changing the Display Brightness

You can dim the display.

Press DIMMER.

•Each time you press the button, the brightness level of the display

changes as follows:

DIMMER

On the unit

From the remote control

Dimmer Much dimmer

Canceled

(Normal display)

Changing the Source Name

When you have connected an MD recorder to the TAPE/MD IN jacks or the DBS tuner to the TV SOUND/DBS IN jacks on the rear panel, change the source name which will be shown on the display when you select the MD recorder or DBS tuner as the source.

On the unit ONLY:

When changing the source name from

“TAPE” to “MD”:TAPE/MD

1. Press TAPE/MD.

2.Press and hold TAPE/MD until

“ASSGN. MD” appears on the display.

	ANALOG	SPEAKERS	1
L	R

SUBWFR			VOLUME