|
| Edit From A Camcorder |
| Slide the TV/CABLE/DBS/DVD switch to DVD. | |
|
|
|
| ||
|
|
|
|
| |
|
|
|
| 1 Make connections. | |
You can use a camcorder as the source player and your unit as the | |||||
| A If the camcorder has no | ||||
recording deck. |
| ||||
| — connect the camcorder’s Audio/Video output connector to the | ||||
|
|
|
|
A If the camcorder has no | unit’s [AUDIO IN | ||||
|
|
|
| front panel. | |
|
|
|
| ● When using a monaural camcorder, connect its AUDIO OUT | |
|
|
|
| connector to the [AUDIO L] input connector on your unit. | |
|
|
|
| B If the camcorder has an | |
|
|
|
| — connect the camcorder’s Audio/Video output and | |
|
|
|
| output connectors to the unit’s [AUDIO IN | |
|
|
|
| ||
|
|
| Recorder | 2 Press VCR/DVD repeatedly to select the recording deck. | |
To | To [AUDIO IN | 3 Press INPUT SELECT +/– on the unit or INPUT +/– on the | |||
| |||||
[VIDEO |
|
|
| remote control to select | |
IN |
|
|
| ● Set “FRONT AUX | |
|
|
|
| ||
|
|
|
| or | |
| Audio/Video cable |
|
| connector being used. ( pg. 59) This setting is also applied to the | |
|
|
| VCR deck. | ||
| (not supplied) |
|
| ||
|
|
| 4 For VCR deck only | ||
|
|
|
| ||
|
|
|
| ||
|
|
|
| 5 Press REC MODE repeatedly to set the recording mode. | |
|
|
|
| ||
|
|
|
| 6 Start playback on the camcorder slightly before the actual point | |
| To Audio/Video Player |
| from where you wish to start dubbing. | ||
|
| For VCR deck only | |||
| output |
|
| ||
|
|
| Press 7 and 9 simultaneously to set to record pause mode. | ||
|
|
|
| ||
|
|
|
| 7 Press 7 on the unit to start recording. Or while holding 7, press | |
|
|
|
| 4 on the remote control. The dubbing starts. | |
B If the camcorder has an | For VCR deck only | ||||
After about 10 seconds, press 4 to start recording. | |||||
|
|
|
| ||
|
|
|
| 8 Press 8 on the unit, then stop playback on the camcorder. | |
|
|
|
| NOTES: | |
|
|
|
| ● All necessary cables can be obtained from your dealer. | |
|
|
|
| ● Refer to the camcorder’s instruction manual for operating procedure. | |
|
|
|
| ● The quality of dubbed picture becomes poorer than that of the | |
|
|
|
| original. | |
|
|
|
| ● When you select “EDIT” to dub tapes in step 4, be sure to select | |
|
|
|
| “AUTO” (or “NORM” when “VIDEO CALIBRATION” is set to “OFF”) | |
To | To [AUDIO IN | Recorder | after you finish dubbing the tapes. | ||
| |||||
IN |
|
|
|
| |
| Audio/Video cable (not supplied) |
|
| ||
| To Audio/Video |
|
|
| |
| output |
|
|
| |
|
|
|
| ||
| (supplied) |
|
|
| |
| To | Player |
|
| |
|
|
|
|