JVC XV-SA72SL Speaker setting, Speaker Channel setting, Select the speaker to be set using Cursor

Initial settings

SCREEN SAVER

A television monitor screen may be burned out if a static picture is displayed for a long time. To prevent this, the unit automatically activates the screen saver function if a

Speaker setting

Speaker Channel setting

static picture, such as an on-screen display or menu, is displayed for over 5 minutes.

Select the speaker configuration type according to your speaker

PREFERENCE1	PREFERENCE2	SPK.SETTING
		5.1 CH.
		LEVEL

•	MODE 1
	The current picture gets
	dark.
•	MODE 2
	The “screen saver” picture
	appears and its brightness

PREFERENCE1	PREFERENCE2 SPK. SETTING
DIGITAL AUDIO OUTPUT		STREAM/PCM
DOWN MIX		OFF
COMPRESSION		OFF
DTS BASS MANAGEMENT		OFF
AUTO STANDBY		OFF
SCREEN SAVER		MODE1
AV COMPULINK MODE		DVD1
PRESS	KEY

system. Normally, simply select “5.1 CH.” or “2 CH.”. However, by selecting “EXPERT”, you can make fine tuning to match your speaker system.

		DELAY
		F. SP	Large
		C. SP	Small
		R. SP	Small
		BASS	S.woofer
PRESS	KEY	TEST TONE

changes.

• OFF

• 2 CH.

When you connect to a 2-channel amplifier or TV.

The screen saver function is off.

NOTES

•The monitor screen of a projector or projection TV is easily burned out if a static picture is displayed for a long time. Be careful not to allow the monitor screen to be burned out when you set the SCREEN SAVER mode to “OFF”.

•The TV screen may be garbled when you set the SCREEN SAVER mode to “MODE 1”. In this case, set to another mode.

•When a static picture is displayed for a long time during playback, the screen saver function is always activated in “MODE 1” regardless of whether you select “MODE 1” or “MODE 2”.

AV COMPULINK MODE

•	5.1 CH.
	When you connect to a 5.1-channel amplifier and use
	the front, rear, center and sub-woofer speakers.
•	EXPERT
	When you want to make fine tuning to match your
	speakers. The following five setting items are
	available.

NOTES

• When selecting “5.1 CH.” or “EXPERT”, set “DOWN

MIX” to “OFF” (see page 58).

• The Dolby Digital LFE (Low Frequency Effect) signal is

always fed from the SUBWOOFER output on the rear

panel of the unit regardless of speaker setting.

• If you connect the unit's digital output to an external

Dolby Digital or DTS decoder (and set the “DIGITAL

AUDIO OUTPUT” option to “STREAM/PCM”), the

If you use the AV COMPU LINK system, you must set this item correctly.

Select from the three options: “DVD1”, “DVD2” and “DVD3” according to the equipment to be connected.

See page 64.

PREFERENCE1	PREFERENCE2		SPK. SETTING
DIGITAL AUDIO OUTPUT		STREAM/PCM
DOWN MIX			OFF
COMPRESSION			OFF
DTS BASS MANAGEMENT			OFF
AUTO STANDBY			OFF
SCREEN SAVER			MODE1
AV COMPULINK MODE			DVD1
PRESS	KEY

speaker setting above is not effective. Make the speaker

setting of the external decoder properly.

Speaker size settings

(available only when selecting EXPERT)

Sets the speaker sizes
according to your	PREFERENCE1 PREFERENCE2		SPK.SETTING
speakers.			EXPERT
			LEVEL
			DELAY
			F. SP	Large
			C. SP	Small
			R. SP	Small
			BASS	S.woofer
	PRESS	KEY	TEST TONE

Initial settings

1 Select the speaker to be set using CURSOR

5/∞.

•F.SP: Front speakers

•C.SP: Center speaker

•R.SP: Rear speakers

59