REQUIRED TEST EQUIPMENT:

Multimeter (for testing continuity)

CHECKING CONTINUITY WITH THE MULTIMETER

1.Rotate the thermostat shaft until an audible click is heard.

2.Rotate the thermostat shaft left and right ten times causing the switch to click on and off ten times, while using the Multimeter to verify continuity.

3.If the switch does not show continuity during all ten trials, replace the thermostat.

WARNING

Disassembling the thermostat will void the ther- mostat warranty.

1.Set compression ring onto capillary end of bulb finger tight, 1/2” from end of capillary.

2.Insert new thermostat bulb through control panel back.

3.Apply oil resistant flexible sealant onto compres- sion fitting thread before installing fitting into fryer vessel.

4.Position bent portion of bulb against far right heat transfer tube and install compression fitting snugly into fryer vessel.

5.Adjust bulb so at least 2” of bent portion of it is next to heat transfer tube and tighten compres- sion nut onto compression fitting for fryer 10x11, 18 & up. The end of thermostat bulb should touch the burner tube for 14" fryers.

6.Replace burners.

7.Replace control panel back.

8.Slide back fabric shield over capillary and care- fully coil capillary. Avoid crimping.

9.Reconnect wires to thermostat body.

10.Replace two screws which hold thermostat body to control panel.

11.Replace control panel.

12.Replace three retaining screws and washers which hold dial plate in place.

13.Replace thermostat knob.

14.Connect electric power source. Turn on gas and pilots.

15.Boil out fryer.

16.Refill fryer with oil to “fill level line”.

17.Start fryer, preheat and calibrate with thermometer.

“KEATING” ELECTRONIC TIMER (PART # 023709)

HOW TO PROGRAM THE “KEATING”

ELECTRONIC TIMER

Make certain power to the timer has been OFF for at least 30 seconds. Then PRESS and hold down the UP arrow but- ton while turning the rocker power switch to the ON posi- tion.

Note: If power switch does not turn off timers, the unit must be unplugged (two people may be needed).

The timer will turn ON and the display will now be indicating

 

 

 

– – –

 

– •– –

 

OR

•

The BEEPER will BEEP 4 times.

If STEP 1 was OK, proceed to STEP 2. If not, retry Step 1 making sure the power was OFF for at least 30 seconds or more.

10

Page 11 Page 13
Page 12
Image 12
Keating Of Chicago 2000 Keating Electronic Timer HOW to Program the Keating, Checking Continuity with the Multimeter
Page 11 Page 13

2000 specifications

Keating of Chicago 2000 is a remarkable example of innovation in the realm of high-performance vehicles, combining technology, design, and engineering prowess to create a stunning automobile that stands out. This vehicle is a product of the renowned Keating brand, known for its focus on creating bespoke sports cars that offer thrilling performance while maintaining luxurious comfort.

One of the standout features of the Keating of Chicago 2000 is its powerful engine. It is equipped with a high-performance V8 engine, capable of delivering exceptional horsepower and torque. This engine allows the vehicle to accelerate from 0 to 60 mph in a matter of seconds, showcasing the raw power that enthusiasts crave. The engineering behind the engine includes advanced fuel injection systems and turbocharging, enhancing efficiency and performance.

The chassis of the Keating 2000 is meticulously engineered using lightweight materials such as carbon fiber and aluminum. This contributes not only to the vehicle’s agile handling but also to improved fuel efficiency. The design incorporates a low center of gravity, allowing for enhanced stability during high-speed cornering.

Aerodynamics plays a crucial role in the design of the Keating of Chicago 2000. The body features sleek lines and an aggressive stance, which minimize drag and improve overall handling. Active aerodynamic components, such as adjustable spoilers, further optimize the vehicle’s performance at various speeds, making it suitable for both track days and everyday driving.

Inside, the Keating of Chicago 2000 boasts a luxurious and highly customizable interior. Premium materials such as leather, Alcantara, and bespoke wood finishes create an unparalleled ambiance. The latest technology is integrated seamlessly, including a state-of-the-art infotainment system, advanced navigation, and an audiophile-quality sound system.

Safety features are also a critical aspect of the Keating 2000. Equipped with advanced driver-assistance systems, the vehicle enhances driver confidence and promotes safe driving. Features such as adaptive cruise control, lane-keeping assist, and a comprehensive airbag system underline the brand’s commitment to safety without compromising the exhilarating driving experience.

In conclusion, the Keating of Chicago 2000 sets a benchmark in the luxury sports car segment, exemplifying a blend of performance, technology, and comfort. With its powerful engine, lightweight chassis, aerodynamic design, luxurious interior, and advanced safety features, it offers an unmatched driving experience that appeals to automotive enthusiasts and luxury car aficionados alike.
Top Page Image Contents